Directed RS2.1 Скачать руководство пользователя страница 50

Страница: 50 / 55

Release the Valet®/Program switch.

Press and release the Valet®/Program switch within 5 seconds. The LED will flash in groups

indicating the last two zones that triggered the unit for one minute or until the ignition

is turned off.

NOTE:

The Warn Away triggers are not stored to memory and will not be reported.

safety check

Before vehicle reassembly, the remote system must be checked to ensure safe and trouble-free operation. The

following test procedure must be used to verify proper installation and operation of the system. The installation

must be completed before testing, including connection to the brake switch and hood switch.

1. Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the remote start system. Once the

engine is running, press the brake pedal. The engine should shut down immediately. If the engine contin-

ues to run, check the brake circuit connection.

2. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the hood. Activate the remote start

system. The vehicle should not start. If the starter engages, check your hood pin and connections.

NOTE:

If programmed for Diesel Mode, the system will turn on the ignition, but the starter should

not engage with the hood open.

3. Test the NEUTRAL SAFETY shutdown circuit:

IMPORTANT!

Make sure there is adequate clearance to the front and rear of the vehicle before

attempting this test.

a. Make sure the hood is closed and no other shutdown circuits are active.

b. Set the emergency brake.

c. Turn the ignition key to the run position but do not start the engine.

d. Put the vehicle in Drive (D).

e. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake to shut-

down the remote start system.

Содержание RS2.1
























































Результаты поиска

Содержание RS2.1

Отзывы:

Похожие инструкции для RS2.1

Бренды по названию

Популярные бренды

Directed RS2.1, Руководство по установке

Результаты поиска

Содержание RS2.1

Отзывы:

Похожие инструкции для RS2.1

Бренды по названию

Популярные бренды