Rev.: 20
914
170
Platform: DBALL2
Firmware TL7
:
© 2017 Directed. All rights reserved.
Tire Pressure
Warning ECU
(Behind glove box)
6 5 4 3 2 1
12 11
10
9 8 7
1
8
16
9
Diagnostic
onnector OBDII
C
Remote
Starter
1:
(-) Lock Input
Green:
2:
(-) Unlock Input
Blue:
10:
(-) GWR (Status) Input
Blue/White:
9:
(+) Ignition Input
Pink:
[4]
Autolights Interr. (conn. side):
11
Yellow/Red:
[3]
(-) Parking Lights
, p
:
in 18
Tan
[4]
Autolights Interr. (veh. side):
10
Orange/Red:
[ ]
1
(AC) Tach Output:
5
Violet/White:
(+) Brake
Output:
6
Status
Gray:
(-) E-Brake Status Output:
1
Black/White:
(-) Door Status Output:
3
Green/White:
(-) Trunk Status Output:
4
Red/Black:
SIL:
10
Yellow/Black:
[ ]
2
(-) Hood Status Output:
12
Blue/Red:
CAN
, p
High:
in 6
Violet
SIL:
in 7
Tan
, p
CAN Low:
in 14
White
, p
Headlight
Switch
(+) 12V
(-) Ground
(+) 12V
:
13
Input
Red:
(-) Ground:
14
Black:
[3]
Output
(-) Parking Lights
[1]
(AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
[ ]
2
(-) Hood Status Input
(+) Brake
Input
Status
(-) Ground
(-)
Output
Lock
(-)
Output
Unlock
(-) GWR Output
[4]
:,
p
Autolights
in 19
Green
Make this connection
only
if the vehicle is
equipped with Automatic
Headlamps.
HS CAN High:
3
Tan/Black:
HS CAN Low:
4
Tan:
SIL Interr. (conn. side) :
8
Yellow:
SIL Interr. (veh. side) :
9
Orange/Yellow:
SIL:
, p
0
in 1
Blue
(+) 12V Input
(+) Ignition
Output
2
(+) Ignition
Input/Output
1
(+) Starter
Output
1
CUT
CUT
It is important to make sure you do
connect the keysense wire in th
NOT
is
installation or you will encounter issues when attempting to start the vehicle.
20
19
Not required in D2D mode.
Ignition
onnector
C
Fuse Box Connector
Refer to the Vehicle
Wiring
Reference Information
for wire
and connector details.
4 3 2 1
8 7 6 5
1
Installation Type 9
Page 20
P#: XKD2D65
TX
(-) Ground
RX
(+)12V
10
RF
Prog
utton
.B
LED
4
14
12
2
DBALL2
With the exception of the
Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).
OBDII
s
[ ]
1
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;
refer to the Vehicle Application Guide for compatibility.
[ ]
2
If
equipped
factory
. If not, a hood switch must be installed and connected to the remote starter.
[ ]
3
Parking light output only required if Parking Lights are not supported in data.
[4]
Autolights Interrupt only required if vehicles are equipped with Autolights.