Directed Electronics Valet 561T Скачать руководство пользователя страница 30

Страница: 30 / 34

The LED will now report the last system shutdown by flashing for one minute in the following grouped patterns:

The LED will stop flashing when the ignition is turned on.

timer mode

This unit can be programmed to start and run the engine every three hours. The engine will run for the pro-

grammed run time and then shut down. After three hours, the unit will restart the engine. A maximum of six

cycles can occur.

IMPORTANT!

Timer Mode should be used only in open areas. Never start and run the vehicle in an

enclosed space such as a garage or carport.

To enter Timer Mode:

1. Turn the ignition on.

2. Press and HOLD the activation input to the remote start.

3. Turn the ignition off while holding the activation input.

4. Release the activation input.

The parking lights (if connected) will flash four times and the engine will start. The system is in Timer Mode. The

engine may be allowed to run for its programmed run time, or the activation input can be used to shut down the

engine. Either way, the remote start system will restart the engine again in three hours. Timer Mode is exited

automatically after the sixth run cycle.

LED SHUTDOWN
FLASHES

MODE

One

System timed out

Two

Over-rev shutdown

Three

Low or no RPM

Four

Transmitter Shutdown (or optional push-button)

Six

(-) Shutdown

Seven

(-) Neutral safety shutdown (H2/6 BLACK/WHITE)

Eight

Wait-to-start timed out

Содержание Valet 561T



































Результаты поиска

Содержание Valet 561T

Отзывы:

Directed Electronics Valet 561T, Руководство по установке, Страница: 30 / 34

Результаты поиска

Содержание Valet 561T

Отзывы: