Directed Electronics Valet 561T страница 27 Скачать руководство пользователя

Страница: 27 / 34

features menu

The factory default settings are indicated in

bold

text in the table below.

FEATURE

DEFAULT - LED ON SETTING

LED OFF SETTING

NUMBER

(PRESS CHANNEL 1)

(PRESS CHANNEL 2)

Engine checking on

Engine checking off

Tachometer checking type

Voltage checking type

12 minutes run time (1)*

24 minutes (2)*, 60 minutes (3) run time

Flashing parking light output

Constant parking light output

Cranking time 0.6 sec. (1)

Cranking time 0.8 (2), 1.0 (3), 1.2 (4), 1.4 (5),
1.6 (6), 1.8 (7), 2.0 (8), 4.0 (9) sec.

Voltage check high level

Voltage check low level

No function

Activation pulse: 1 (1)

Activation pulses: 2 (2)

, 3 (3)

Ignition/accessory output: Ignition

Ignition/accessory output: Accessory

Accessory state during wait to start: OFF

Accessory state during wait to start: ON

2nd status output: Normal

Rear defogger latched/pulsed

No function

*NOTE:

The number in parentheses indicate the number of times the LED will flash

Содержание Valet 561T



































Результаты поиска

Содержание Valet 561T

Отзывы:

Похожие инструкции для Valet 561T

Бренды по названию

Популярные бренды

Directed Electronics Valet 561T, Руководство по установке

Результаты поиска

Содержание Valet 561T

Отзывы:

Похожие инструкции для Valet 561T

Бренды по названию

Популярные бренды