Directed Electronics 3500 ESP Скачать руководство пользователя страница 21

Страница: 21 / 44

plug-in LED and valet/program switch

These plug into the module. The status LED plugs into the small two-pin socket, while the Valet®/Program switch

should be plugged into the larger blue two-pin connector. The status LED fits in a

-inch hole.

Status LED

Valet®/Program Switch

programmer interface, 3-pin port

The black 3-pin port is provided for personal computer programming of the unit. The unit can also be programmed

using the Bitwriter (

p/n 998T

). When using the optional PC Interface module, or hand-held programmer, it is

possible to configure any and all of the programmable functions as well as lock the Transmitter/Receiver and

System Features Learn Routines so that unauthorized users cannot change the configuration or program trans-

mitters to the unit.

When the learn routines have previously been programmed using an optional hand-held system programmer

(

p/n 998T

) or PC Interface module, they may have been locked. Before proceeding with reprogramming

the learn routines, they must be unlocked with either the 998T or the PC Interface module - this cannot be done

manually with the Valet switch.

Содержание 3500 ESP













































Результаты поиска

Содержание 3500 ESP

Отзывы:

Похожие инструкции для 3500 ESP

Бренды по названию

Популярные бренды

Directed Electronics 3500 ESP, Руководство по установке

Результаты поиска

Содержание 3500 ESP

Отзывы:

Похожие инструкции для 3500 ESP

Бренды по названию

Популярные бренды