Directechs FORD13 Скачать руководство пользователя страница 19

Quick Reference Guide

Pit stop/idle mode

1

Stop

 the vehicle in a safe parking spot and 

put

 the 

gear in Park (P).

Put 

gear in 

Park

2

Press

 the Remote Start button on the transmitter.*

The parking lights will flash once to indicate the 
vehicle is now in Pit Stop Mode.

Parking lights flash x1

14:36

Press Remote 

Start button*

&

3

It is safe to 

leave

 the engine running and 

exit

 the 

vehicle with the factory remote in hand.

Note

: We recommend that you always 

lock

 the 

doors of your vehicle when leaving it unattended.

14:36

Exit vehicle 

with remote

* Icon and remote appearance may differ depending on the model purchased.

List of available commands

Note that the information below is for many Viper, Clifford, Python, Avital and 
Automate models. Icons and commands may differ depending on the model and 
options purchased. Refer to your authorized installation center for more specific 
information.

Button(s)

Actions
Press

 & 

hold

 for 1 second to lock.

Press

 & 

hold

 for 1 second to unlock.

   

*

Press

 & 

hold

 for 1 second to remote start.

 

  *

Press

 & 

hold

 for 5 seconds to activate the trunk release (optional).

* Icon and remote appearance may differ depending on the model purchased.

Sending commands to your vehicle

Whether you want to remote start the engine, lock/unlock the doors or pop the trunk, 
there are 3 possible ways you can send commands to your vehicle, using the:
•  Factory remote.
•  Aftermarket remote.
•  Directed SmartStart application via your smartphone.

If applicable, you can also start the engine remotely by pressing the Lock button 3 
times quickly on your factory remote.

Vehicle takeover with regular key

1

Close

 the vehicle doors, hood and trunk, then 

send

 

the Remote Start command to start the vehicle.*

14:36

Press Remote 

Start button*

2

Send

 the Unlock command on the factory or 

aftermarket remote.*

14:36

Press Unlock on 

either remote*

3

Enter

 the vehicle, 

insert

 your key in the ignition 

barrel, and 

turn

 it to the ON position.

START

Key OUT

ON

OFF

START

Key IN

ON

OFF

START

Key IN

ON

OFF

START

Key IN

ON

OFF

Enter

vehicle

&

4

Depress

 the brake pedal, 

put

 the car in gear and 

drive

 off.

Ready to 

drive off

* Icon and remote appearance may differ depending on the model purchased.

Directed Digital Solutions FORD13

© 2020-04-28 Directed. All rights reserved.

Содержание FORD13





















Отзывы: