Dionex ICS-900 Скачать руководство пользователя страница 60

Страница: 60 / 142

ICS-900 Operator’s Manual

Doc. 065215-02 9/09

The table below lists the ICS-900 error messages. For troubleshooting assistance,
refer to the page indicated in the table

This message may appear at when the ICS-900 power is turned on. If the
message appears at other times, it indicates a problem.

To troubleshoot:

1. Perform the suppressor inline quick start procedure:

a. Disconnect the separator column outlet line from the suppressor

ELUENT IN

port and disconnect the cell inlet line from the suppressor

ELUENT OUT

port. Use a union to connect these two lines.

b. Turn on the pump flow and allow the suppressor to regenerate for

10 minutes.

c. Turn off the pump and allow the suppressor to hydrate for 20 minutes.

d. Reconnect the separator column outlet line and cell inlet line to the

suppressor ports.

2. If the high background persists:

•

Prepare fresh eluent (see

Section 3.4

•

Prepare fresh regenerant (see

Section 3.5

Alarms and Error Conditions

See

Conductivity exceeds limit.

page 52

Flow rate calibration error.

page 53

Load/inject valve error.

page 53

Module data buffer overflow. Data may have been lost.

page 54

Pump motor lost control.

page 54

Pump pressure hardware error.

page 54

Pump pressure slope calibration error.

page 55

Remaining eluent below 200 mL.

page 55

The system pressure is below the low pressure limit.

page 56

The system pressure has exceeded the high pressure limit.

page 56

Conductivity exceeds limit.

Содержание ICS-900















































































































































Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды

Dionex ICS-900, Руководство оператора

Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды