DiO MVR-40-10RF Скачать руководство пользователя страница 9

www.getdio.com

EN | 9

We recommend that you adjust the end stops gradually by only turning the adjustment screws 

a few turns at a time. Warning, depending on the size of your shutter, you may have to turn the 

screws several dozen times to get the correct setting.

Close the housing again in accordance with the instructions for your shutter or blind, taking care 

not to leave the power cable in the housing so that it does not impede the shutter from rolling 

up, or the radio antenna in order to optimise the range of the signal and thus its connection with 

your DiO 1.0 control unit(s). 

- If the shutter stops before the required up position, increase the end stop by gradually turning 

the bottom screw anti-clockwise (towards '+') with the adjustment tool provided. The shutter 

will gradually go up as you turn the screw. If the adjustment lasts more than two minutes, press 

the ON ('I') button to start raising the shutter again.

 - If the shutter reaches the required up position before stopping automatically, 

stop it 

immediately

 by pressing the ON ('I') button on the remote control unit, lower it again by 

pressing the OFF ('O') button on the remote control unit, and correct it by gradually turning 

the bottom screw clockwise (towards '-') with the adjustment tool. Press the ON ('I') button on 

the remote control again to open the shutter and check if the shutter stops at the required up 

position. Repeat the operation until it reaches the required position.

-

+

-

+

-

+

IV.2

Fully closed

Press the OFF ('O') button on the remote 

control. 

Partial closure of the shutter

Press the OFF ('O') button on the remote 

control to start closing the shutter. Press the 

same button again to stop the shutter at the 

required position.

Fully open

Press the ON ('I') button on the remote control. 

Use

Содержание MVR-40-10RF













Отзывы: