Dinstar DWG2000E Скачать руководство пользователя страница 57

Страница: 57 / 92

DWG2000E/F/G GSM/CDMA VoIP Gateway User Manual

_______________________________________________________________________________

Shenzhen Dinstar Technologies Co., Ltd.

need set Yes, to avoid that the devices can not call in

Allow call from IP to PSTN without Registration

Refer to "SIP Configuration" ->

"Is register”. If "Is register" setting is no, this option

need set Yes ,to avoid that the devices can not call out

Reject Anonymous call from IP to PSTN

The incoming anonymous calls will be rejected

Use # as End Key

In General, SIP phones are based on # as the end, if this option is set to No, the

dial-up will end expires dial-up time

Interdigit Timeout

Bit of between the dialing time ,over the time will be seem as end of dia

Call Delay

Default value is 0s.

4.12.2 SIP Parameter

This section is describes how to configure SIP server and SIP parameters.

Configure SIP server and Outbound Proxy server

SIP Server Address and Port

Used for configure SIP server address and port, the address can be IP Address, also

can be a domain name which can be resolved by DNS server

Check NET Status

Default is No. if it set to Yes, the gateway will send SIP OPTION periodic to check

health status between gateway and SIP server.

Outbound Proxy

Outbound proxy, it mainly used in firewall / NAT environment. That make the

Содержание DWG2000E





























































































Результаты поиска

Содержание DWG2000E

Отзывы:

Похожие инструкции для DWG2000E

Бренды по названию

Популярные бренды

Dinstar DWG2000E, Руководство пользователя

Результаты поиска

Содержание DWG2000E

Отзывы:

Похожие инструкции для DWG2000E

Бренды по названию

Популярные бренды