background image

THE FOLLOWING MUST BE APPLIED WHEN
FIXING THE HEATER TO THE WALL BRACKET

7.

7.

i) If no skirting board is present secure the heater through

the wall bracket slots closest to the wall.

ii) If 100mm (4in.) skirting is present secure the heater through

the outer slots.

iii) If skirting taller than 150mm (6in.) is present this must be

reduced to 150mm (6in.) over the entire width of the heater

plus 25mm (1in.) at each end.

Do not fully tighten these screws until the bricks are loaded
into the heater as some settling of the heater may occur.

NOTE: NEVER REMOVE THESE SCREWS WITHOUT
FIRST UNLOADING THE HEATER.

Remove the front panel by removing the two self tapping

screws along its bottom edge.  With hands positioned on

each side of the panel, lift upwards to unhook the top edge

whilst pressing down on the top panel with your thumbs.  The

panel can now be lifted clear and set to one side.

8.

9.

Remove the inner front by removing the screws along its

top and sides.  As the front insulation is attached care

must be taken when lifting this panel from the heater and placing

it to one side.  Remove the internal packing by sliding it up and

off the elements taking care not to damage the insulation.

10.

Remove one element to allow access for the back rows

of bricks.  On the 724N remove the element to the right

of centre, on the 718N remove the central element, on the

712N the left hand element should be removed and, on the

706N, there is only one element.

Loosen the two screws securing the element tails in the ceramic

connector block, and lift the element up and out of the heater.

Carefully fit the bottom row of the back layer of bricks

placing the two end bricks in position first with the recess

towards the element.  Fit the top row of bricks also with the
recess towards the element.

11.

Refit the element which has been removed by feeding
the tails down through the hole in the base insulation and

into the connector block.  Ensure the element is fully pushed
home then securely tighten the two screws in the block.

12.

12.

Fit the front layer of bricks again with the recess towards
the element.  The complete core will comprise:

706N - 1 x 4 Brick Columns
712N - 2 x 4 Brick Columns
718N - 3 x 4 Brick Columns
724N - 4 x 4 Brick Columns

Replace the inner front complete with insulation by

locating its bottom edge behind the front lip of the

chassis and inserting retaining screws along the top and

both sides.

14.

For models 712N, 718N and 724N only, check that

the flap mechanism operates freely on its hinges and

that with the output control set to 1 the flap is correctly seated

in its closed position.

15.

Feed the mains cable through the cable clamp and

make connections as marked on heater.  Pull back

any slack through the clamp and tighten clamping screw.

16.

16.

WARNING - This appliance must be earthed

Replace outer front panel and grille by hooking the
grille into its retaining slot on the top panel and lowering

it into position.  Secure the front panel with the two self tapping
screws.

17.

17.

Check that the screws securing the heater to the wall
bracket have been fully tightened.

IT IS ESSENTIAL THAT ALL SCREWS ARE REPLACED
TO ENSURE EARTH CONTINUITY.

Once installed do not attempt to reposition the heater without
first obtaining the services of a competent electrician.

18.

8.

9.

10.

13.

Содержание XMX706N

Страница 1: ...ith the heater does not occur Ê WHERE YOUNG CHILDREN INFIRM PERSONS OR THE AGED ARE PRESENT THIS APPLIANCE MUST BE ADEQUATELY GUARDED Contact your installer or the manufacturer for further advice Ê This appliance is very heavy and must be securely fixed to a wall DO NOT UNDER ANY CIRCUMSTANCES ATTEMPT TO MOVE OR REPOSITION THIS HEATER WITHOUT SEEKING EXPERT ADVICE Ê To maintain stability it is ess...

Страница 2: ...level surface at least 75mm from any end wall and at least 250mm below any shelf or similar projection Cut away any gripper rod or carpet which would prevent the heater sitting firmly on the floor 4 4 Mark the position of the two outside corners of the wall bracket with the heater pushed tight against the wall Remove the wall bracket from the heater by removing the screw at each end Place the heat...

Страница 3: ...ent up and out of the heater Carefully fit the bottom row of the back layer of bricks placing the two end bricks in position first with the recess towards the element Fit the top row of bricks also with the recess towards the element 11 Refit the element which has been removed by feeding the tails down through the hole in the base insulation and into the connector block Ensure the element is fully...

Страница 4: ... of the heater To adjust the controls on the heater use a coin and engage it in the slots provided on the top surface of the knob There are no user adjustable controls on the XMX706N For models XMX712N 718N 724N only Initially set the input to 4 If the heater does not maintain a satisfactory room temperature the following day this setting should be increased Conversely if the room temperature is t...

Отзывы: