The appliance must be wall mounted as follows:
1.
Firstly remove the polystyrene inserts
which secure the elements during transportation by removing the screw and washer at each end
of the grille. Lift the grille off carefully and dispose of the inserts.
2.
Before positioning the heater, firstly observe the clearances shown on page 1
(Fig.1)
3.
Remove the screw
(3)
from the back plate
(1)
and remove the terminal block cover
(2) (Fig.2)
4.
Rotate the back plate
(1)
backwards through 90°
(Fig.2)
5.
Draw a line along the top edge of the back plate and mark the fixing positions through the two holes at either end of the terminal block.
6.
Drill two holes and use the wall fixings supplied (alternative wall fixings may be required depending on the wall type)
7.
Insert the narrow end of the two cylindrical plastic spacers
(4)
in to the two holes of the back plate
(Fig.3)
8.
Insert the screws
(5)
in to the spacers and screw firmly to the wall
9.
Insert the supply cable through either the left of right cable entry grommet and clamp in to position
10.
Connect the supply cable to the terminal block as follows:
Blue– N (Neutral)
Brown– L (Live)
Green/Yellow–
E
(Earth)
11.
Re-attach the terminal cover
(2)
to cover the electricity supply before switching the heater on
Operation
The indicator window shows a number which corresponds to the number of elements being energised. To switch the heater ON,
Pull and release the cord gently until the number is visible.
IRX1200N
IRX1800N
(0)
- Heater switched OFF
(0) - Heater switched OFF
(1)
- One element energised = 1200Watts (1) - One element energised = 600Watts
(2)
-
Two
elements
energised
=
1200Watts
(3)
-
Three
elements
energised
=
1800Watts
Element Replacement WARNING: DISCONNECT THE POWER SUPPLY before carrying out any
maintenance
1.
Remove the screw and washer at each end of the grill and lift off the grille carefully
2.
Pull off the spade connector at each end of the failed element
3.
Gently slide the element out of the reflector
4.
Fit the replacement element in reverse order of the above instructions taking care
NOT
to touch the element tube with your fingers. Ensure
the grille is secured correctly with the screws and washers.
Cleaning WARNING: DISCONNECT THE POWER SUPPLY before carrying out any maintenance
Before cleaning your heater, switch off the electricity supply to the appliance and allow to cool. The outside of the appliance can be cleaned by
wiping it over with a soft damp cloth and then dried. To remove dust from the reflector and heating elements you can use a brush with long soft
bristles.
After Sales Service
Your product is guaranteed for two years from the date of purchase.
Within this period, we undertake to repair or exchange this product free of charge (subject to availability) provided it has been installed and operated
in accordance with these instructions. Your rights under this guarantee are additional to your statutory rights, which in turn are not affected by this
guarantee.
Should you require after sales service you should contact our Technical Services help desk on 0845 600 5111. It would assist us if you can quote
the model number, date of purchase, and nature of the fault at the time of your call. The Technical Services help desk will also be able to advise you
should you need to purchase any spares.
Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in providing you with a satisfactory
service.
Please retain your receipt as proof of purchase.
Dimplex UK Ltd
Millbrook House
Grange Drive
Hedge End
Southampton
SO30 2DF
UK Technical Services: 8.00am - 5.00pm Mon-Fri and 8.30am-1pm Sat (Oct-March)
Telephone: 0845 600 5111
Fax:
01489 773053
E-mail:
Web-site:
www.dimplex.co.uk
Republic of Ireland Tel: 01 842 4833
All rights reserved. Material contained in this publication may not be reproduced in whole or part, without prior permission in writing from Dimplex UK Limited.
(C) Dimplex UK Limited
