thermostat
knob - see
Fig. 3
heat control
knob - see
Fig. 2
air outlet
Installation and Operating Instructions
08/35198/2 Issue 2
IMPORTANT SAFETY ADVICE
DO NOT use the heater on deep pile carpets or the long hair
type of rugs, or less than 750mm (30") away from any
overhanging surface. Keep combustible materials such as
drapes and other furnishings clear from the front, sides
and rear of the heater. Do not use heater to dry your laundry.
DO NOT use the heater in the immediate surroundings of a
bath, a shower or a swimming pool.
DO NOT place the heater directly below a fixed socket outlet.
WARNING: In order to avoid overheating, do not cover the
heater.
The socket-outlet must be accessible at all times to enable
the mains plug to be disconnected as quickly as possible.
DO NOT COVER or obstruct in any way the air inlet slots in
the top and bottom of the heater, or the air outlet slots at the
front of the heater.
DO NOT operate the heater with the mains lead overhanging
the front outlet grille.
The heater should always be used on a flat, stable surface.
This appliance is not intended for use by children or other
persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it
safely. Children should be supervised to ensure that they
do not play with the appliance.
Warning : In order to avoid a hazard due to inadvertent
resetting of the thermal cutout, this appliance must not be
supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched
on and off by the utility.
THE HEATER CARRIES A WARNING SYMBOL
INDICATING THAT IT MUST NOT BE COVERED.
The instruction leaflet belongs to the appliance and must
be kept in a safe place. If changing owners, the leaflet must
be surrendered to the new owner.
IMPORTANT – If the mains lead of this appliance is damaged,
it must be replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a hazard.
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Electrical connection
This heater must be used on an ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
This heater is fitted with a rewirable plug incorporating a 13 amp
fuse. In the event of replacing the fuse in the plug supplied, a 13
amp fuse approved by ASTA to BS 1362 must be used. If any
other type of plug is used, a 15 amp fuse must be fitted in the
plug, the adaptor, or at the distribution board.
IMPORTANT : If the plug is not suitable for your socket, the 13
amp plug should be removed. Before wiring the appropriate
plug, please note that the wires in this mains lead are coloured
in accordance with the following code :
BLUE :
NEUTRAL
BROWN :
LIVE
As the colours of the wires in the mains lead may not correspond
with the coloured markings in your plug, proceed as follows :
Connect the
BROWN
wire to the terminal marked ‘
L
’ or coloured
RED
. Connect the
BLUE
wire to the terminal marked ‘
N
’ or coloured
BLACK
.
Note :
‘L’ or ‘N’ wire must not be connected to the EARTH
terminal marked ‘E’ or
or coloured
GREEN
or
GREEN AND
YELLOW
. If in doubt, consult your electrician.
Important Operating Information
ACCUMULATION OF FLUFF AND DUST IN THE HEATER MAY
CAUSE THE ELEMENT TO OVERHEAT AND CUT OUT.
THEREFORE IT IS IMPORTANT THAT THE HEATER IS CLEANED
REGULARLY, PARTICULARLY IF THE PRODUCT IS USED OR
STORED IN AREAS WHERE HIGH LEVELS OF DUST AND/OR
FLUFF ARE PRESENT (I.E. BEDROOMS/DRESSING ROOMS)
(see section of instructions titled ‘cleaning’ for details on how
to maintain optimum performance of your heater)
air inlet
handle
mains neon
Fig. 1
Model
(
s
)
Specification
DXFF20TS
2.0kw Switch, Thermostat & Neon
DXFF30TS
3.0kw Switch, Thermostat & Neon
DXFF20TS & DXFF30TS Flat Fan Heaters
