Dimplex Creme RTOPSTV20GC Скачать руководство пользователя страница 7

Symptom

Cause

Corrective Action

The flame effect will 

not start.

Mains plug is not plugged in.

Low water level.

 

Low voltage connector not connected 

properly. (See Fig.5)

The Transducer Unit is not sitting correctly in 

the sump

Check plug is connected to wall socket 

correctly.

Check that the water tank is full and there is 

water in the sump.

Check that the connector is inserted 

correctly. (See Fig.5)

Ensure the Transducer in sitting down into 

the moulded recess in the  sump

The flame effect is too 

low.

Flame effect control knob is set too low.

(See Fig.10)

The Metal Disc in the transducer might be 

dirty (See Fig.14)

The wire from the Transducer Unit is sitting 

over the metal disc

Increase level of flame by turning Control 

knob ‘D’ to the left slowly. (See Fig.10)

Clean the Metal Disc with soft brush 

supplied. (See Fig.14) See ‘Maintenance.’ for 

a step by step procedure.

Direct the wire to the back of the sump and 

make sure it sits into the side slot exiting the 

sump.

Unpleasant smell 

when unit is used.

Dirty or stale water.

Using unfiltered tap water.

Clean the unit as described under 

maintenance.

Use only filtered tap water.

The flame effect has 

too much smoke.

Flame effect setting is too high.

Turn the flame effect  Control knob ‘D’ to 

the right, about ¼ a turn, at a time. Give the 

flame generator some time to adjust to the 

new setting. (See Fig.10)

Main lamps are not 

working and there are 

no flames or smoke.

There is no water in the water tank

Follow instructions under 

Maintenance

,  ‘Filling the water tank’.

Check the plug is connected to the wall 

socket correctly and that Switch ‘A’ Fig. 10 is 

in the ‘ON’  ( 

) position.

Troubleshooting

PATENT / PATENT APPLICATION

Products within the Optimyst range are protected by one or more of the following patents and patent applications:

Great Britain GB 2402206, GB 2460259, GB 2460453 , GB 2418014, GB 2465738, GB 2449925, GB 2465537 , GB

2455277 , GB1020534.2, GB1020537.5, GB1110987.3

United States US 7967690, US 2010299980, US 2011062250, US 2008028648, US 13/167,042

Russia RU2008140317

European EP 2029941, EP 2201301, EP 2315976, EP 1787063, EP07723217.1 , EP11170434.2, EP 11170435.9

China CN 101883953, CN 200980128666.2, CN 101057105, CN 101438104

Australia AU 2009248743, AU 2007224634

Canada CA 2725214, CA 2579444, CA 2645939

International Patent Application WO 2006027272

South Africa ZA 200808702

Mexico MX 2008011712

Korea KR 20080113235

Japan JP 2009529649

Brazil BR P10708894-9

India IN 4122/KOLNP/2008

New Zealand NZ 571900

Содержание Creme RTOPSTV20GC













Отзывы: