10
www.dimplex.com
2. Slide the controls assembly out toward the front of the
unit.
CAUTION:
Ensure that the assembly is removed care-
fully, ensuring that no wires are caught or over strained.
3.
Locate the switchboard (Figure 10).
4. Disconnect the wiring harness from the switchboard.
5. Remove the switchboard by loosening the nuts on the
spacer stands.
6. Install the new switchboard on the space stands.
7. Reconnect the wire harness onto the back of the
switchboard in its original configuration.
8. Reassemble in the reverse order as above.
CAUTION:
When re-installing, be sure the wires are
guided and tucked into the proper openings along the right
side so they are not pinched and allows enough space to
reinstall the panel.
RELAY BOARD REPLACEMENT
WARNING:
Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
CAUTION:
If unit was operating prior to servicing allow
at least 10 minutes for lights and heating elements to cool
off to avoid accidental burning of skin.
Tools required:
Phillips head screwdriver
Needle nosed pliers
CAUTION:
Follow “Preparation for Service” instructions
before proceeding.
1. Remove the 2 screws, that secure the controls assem-
bly (Figure 9), located at the top of the mirror on the
right side of the unit.
2. Slide the controls assembly out toward the front of the
unit.
CAUTION:
Ensure that the assembly is removed care-
fully, ensuring that no wires are caught or over strained.
3.
Locate the relay board (Figure 10).
4. Transfer the wiring connections from the existing board
to the new board.
!
NOTE:
Using a flat head screwdriver gently pry between
the end of the connectors and the board to release the
wires.
5. Remove the relay board off the plastic mounts by
pinching the plastic mounting tabs with needle nose
pliers. Pull the old board off.
6. Line up the holes on the board and gently press the
new board onto the mounts. Make sure the board is
secure.
7. Reassemble in the reverse order as above.
CAUTION:
When re-installing, be sure the wires are
guided and tucked into the proper openings along the right
side so they are not pinched and allows enough space to
reinstall the panel.
AD/DC ADAPTER REPLACEMENT
WARNING:
Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
CAUTION:
If unit was operating prior to servicing allow
at least 10 minutes for lights and heating elements to cool
off to avoid accidental burning of skin.
Tools required:
Phillips head screwdriver
CAUTION:
Follow “Preparation for Service” instructions
before proceeding.
Tools required:
Phillips head screwdriver
1. Remove the decorative acrylic ember-bed pieces from
the media tray, which lies along the bottom of the inte-
rior Partially Reflective Glass. A medium sized con
-
tainer such as a bucket or a box will be needed to keep
the acrylic ember-bed pieces together.
2. Remove the 2 screws, that secure the controls assem-
bly (Figure 9), located at the top of the mirror on the
right side of the unit.
3.
Remove the Partially Reflective Glass retaining brack
-
ets by removing the 3 screws on each brackets; (3
brackets in total), located on the left and right side of
the Partially Reflective Glass. (Figure 13)
4.
Remove the Partially Reflective Glass. Carefully place
the glass assembly aside in a safe location.
5. Slide the controls assembly out toward the front of the
unit.
CAUTION:
Ensure that the assembly is removed care-
fully, ensuring that no wires are caught or over strained.
6.
Locate the defective AC/DC adapter (Figure 10).
7. Disconnect wires going to the wire connectors and the
wires that are attached to the display / control board.
(Figure 14)
!
NOTE:
Using a flat head screwdriver gently pry between
the end of the connectors and the board to release the
wires.
8. Remove the four screws that secure the AC/DC
adapter bracket to the controls assembly.
9. Install the new AC/DC adapter and install all wiring con-
nections.
10. Reassemble in the reverse order as above.
CAUTION:
When re-installing, be sure the wires are
guided and tucked into the proper openings along the right
side so they are not pinched and allows enough space to
reinstall the panel.
