background image

2002 Dimension One Spas Export Owner’s Manual 

 
 

IMPORTANT SAFETY INSTRUCTIONS 

READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY 
When installing and using this equipment, basic safety precautions should always be followed, including: 

 

 

    Danger 

Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by 
children. To avoid accidents, ensure that children cannot use this spa unless they are supervised at 
all times. 

 

 

 

   Warning 

A grounding wire connector is provided on this spa to connect a minimum No. 8 AWG (8.4 mm2) 
solid copper conductor between this unit and any metal equipment, metal enclosures of electrical 
equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the spa. 

 

 

 

    Danger 

Risk of Serious Injury or Death. The suction fittings in this spa are sized to match the specific water 
flow created by the pump. Should the need arise to replace the suction fittings or the pump, be sure 
that the flow rates are compatible.  
 
Never operate the spa if the suction fittings are broken or missing. Never replace a suction fitting 
with one rated less than the flow rate marked on the original suction fitting. 

 

 

 

    Danger 

Risk of Electric Shock. Install at least 5 FEET (1.5 m), from all metal surfaces. As an alternative, a spa 
may be installed within 5 feet of metal surfaces if each metal surface is permanently connected by a 
minimum No. 8 AWG (8.4 mm2) solid copper conductor attached to the wire connector on the 
grounding lug, inside the equipment compartment on the equipment can. 

 

 

 

    Danger 

Risk of Electric Shock. Do not permit any electrical appliance, such as a light, telephone, radio, 
television, etc. within 5 feet (1.5 m) of a spa. 

 

 

 

    Danger 

The electrical supply for this spa must include a suitably rated switch or circuit breaker to open all 
ungrounded supply conductors to comply with section 680-42 of the National Electrical Code, 
ANSI/NFPA 70-1993. The disconnect must be readily accessible and visible to the spa occupant but 
installed at least 5 feet (1.5 m), from the spa water. 

 

 

 

   Warning 

To Reduce the Risk of Injury:

 

The water in a spa should never exceed 104° F (40° C). Water 

temperatures between 100° F (38° C) and 104° F (40° C) are considered safe for a healthy adult. 
Lower water temperatures are recommended for young children and when spa use exceeds 10 
minutes. 

 

 

 

   Warning 

To Reduce the Risk of Injury: 
Since excessive water temperatures have a high potential for causing fetal damage during the early 
months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 
100° F (38° C). 

 

   Warning 

To Reduce the Risk of Injury: 
Before entering a spa, the user should measure the water temperature with an accurate 
thermometer since the tolerance of water temperature-regulating devices may vary as much as +/- 
5° F (2° C). 

1

 

Содержание 2002 Arena









































Отзывы: