Dillon AFG 1000N Скачать руководство пользователя

Страница: 9 / 44

The alarm feature operates by setting a band

comprising of two force points, an upper and a

lower, which you select. You configure the alarm

so that a buzzer sounds and/or a light changes from

green to red to signify whether the test force has

gone in or out of the selected band.

The ALARM mode can be entered as described

above in the section entitled Selecting a Mode of

Operation. The alarm is set to operate by configur-

ing the lower and upper alarm points.

Upon entering the

ALARM mode the

first point is

displayed, shown by

a 1 at the top of the

display next to the

ALARM symbol.

To change the value

press the UP or

DOWN arrow

keys. . .

Single key presses

increment or decre-

ment the displayed

value by one display

count, i.e. 1/5000th of

the full scale range in

whichever units are

currently being dis-

played.

Hold the key down for

0.5 seconds to activate

an auto repeat feature.

The value will incre-

ment or decrement

Alarm Mode

Setting the Lower

and Upper Alarm

Points

Point 1 or 2 can be

either the lower or
upper limit. It does
not matter which is
which.

If the mode has been

previously viewed, the
display will show the
last parameter
viewed. Press the
MORE key to scroll
through the list of
parameters until you
see the one you
want.

Содержание AFG 1000N













































Результаты поиска

Содержание AFG 1000N

Отзывы:

Похожие инструкции для AFG 1000N

Бренды по названию

Популярные бренды

Dillon AFG 1000N, Руководство пользователя

Результаты поиска

Содержание AFG 1000N

Отзывы:

Похожие инструкции для AFG 1000N

Бренды по названию

Популярные бренды