Dillon AFG 1000N Скачать руководство пользователя

Страница: 7 / 44

The AFG has the following modes of operation in

addition to the main display mode:

ALARM

In this mode alarm points can be

set and other features pertaining

to the alarms can be configured.

COM

COM stands for COMMUNICA-

TIONS. In this mode you config-

ure serial RS-232 and

MITUTOYO outputs. You can

also configure the internal storage

of readings and their transmission

in this mode.

EXTRA

The EXTRA mode allows all

other instrument characteristics

not previously covered to be

configured.

Follow these steps to select one of the operation

modes:

With the instrument

in the display mode,

press and hold the

MODE key for two

seconds. . .

The current mode

symbol (in this case

DISPLAY) will flash.

Other Modes of Operation

Selecting a
Mode
of Operation

To return to the

main display mode
from any other mode,
press the MODE
key twice.

Содержание AFG 1000N













































Результаты поиска

Содержание AFG 1000N

Отзывы:

Похожие инструкции для AFG 1000N

Бренды по названию

Популярные бренды

Dillon AFG 1000N, Руководство пользователя

Результаты поиска

Содержание AFG 1000N

Отзывы:

Похожие инструкции для AFG 1000N

Бренды по названию

Популярные бренды