Dillenger KT-LCD3 Скачать руководство пользователя страница 28

Страница: 28 / 32

C8 Value

Meter Attribute

Meter uses LCD3 new version of communication protocol, compatible with
LCD1 and LCD3

Meter uses LCD1 and LCD2 old version communication protocol, it is not
compatible with LCD3

As data source for copying parameters, the meter transfers the new LCD3
parameter to other meters

The C12 parameter setting will display on the meter after C11 settings. The KT-LCD3 will
display as follows:

C12 Controller Minimal Voltage Setting

C12 Value

Minimum Voltage (V)

24V Controller

36V Controller

48V Controller

Default Value-2V

Default Value-1.5V

Default Value-1V

Default Value-0.5V

Default Value=20V

Default Value=30V

Default Value=40V

Default Value+0.5V

Default Value+1V

Default Value+1.5V

C12 Display

C12 parameters are settings for the controller's minimum operating voltage (voltage
shortage value). Refer to the following table to calculate the minimum voltage.

C13 Value

ABS Braking Strength

Energy Recovery Efficiency

None

Class 1 Braking Strength

Best energy recovery

Class 2 Braking Strength

General energy recovery

Class 3 Braking Strength

Weaker energy recovery

Class 4 Braking Strength

Poor energy recovery

Class 5 Braking Strength

Bad energy recovery

Содержание KT-LCD3

































Результаты поиска

Содержание KT-LCD3

Отзывы:

Dillenger KT-LCD3, Руководство пользователя, Страница: 28 / 32

Результаты поиска

Содержание KT-LCD3

Отзывы: