manualshive.com logo in svg

Dillenger KT-LCD3, Руководство пользователя, Страница: 26 / 32

Поделиться
Скачать
Dillenger KT-LCD3 Скачать руководство пользователя страница 26

26

C9 is the settings for password feature upon startup. The default value is 0. Refer to the 
following table for definition of the function. 

The C9 parameter setting will display on the meter after C8 settings. The KT-LCD3 will 
display as follows:

C9 Startup Password Setting

C9 Display

C9 Value

Password Function

0

Disabled

1

Enabled

Password Setting Interface

When the feature has been enabled and confirmed by pressing the           button,  the 

display will change to the following. 

From here the rider can set the 3 digit passcode starting from the left and sequentially 
progress to the right. Password value range is 000-999. Select the values with the                 
button,           button, and confirming the selection with the           button. 

PLEASE NOTE:

  If  password  is  forgotten,  the  parameters  can  only  be  copied  (see 

parameter copy) by data source meter prior to being decoded.

C10 Value

Restore Default Setting

n

Disabled

y

Enabled

Содержание KT-LCD3

































Отзывы:

Нет отзывов