Digiway DWPD102A Series, Руководство по установке

Страница: 18 / 52

DIGIWAY PLUS
INSTALLATION MANUAL
EN
STEP V: ADVANCED SETTINGS (Continued...) STEP V: ADVANCED SETTINGS (Continued...)
Advanced Setting
Ex Power Open
Enable / Disable
When enabled, adds one more When enabled, adds one more OPENING OPENING pulse after the regular pulse after the regular OPENING OPENING cycle to cycle to
compensate possible friction or door unbalance. compensate possible friction or door unbalance.
Enable or disable this function with the UP or DOWN buttons and confi rm with OK
Enable or disable this function with the UP or DOWN buttons and confi rm with OK
Default value = DISABLE Default value = DISABLE
8) 8)
Advanced Setting
Ex Power Close
Enable / Disable
When enabled, adds one more When enabled, adds one more CLOSING CLOSING pulse after the regular pulse after the regular CLOSING CLOSING cycle to cycle to
compensate possible friction or door unbalance. compensate possible friction or door unbalance.
Enable or disable this function with the UP or DOWN buttons and confi rm with OK
Enable or disable this function with the UP or DOWN buttons and confi rm with OK
Default value = DISABLE Default value = DISABLE
11) 11)
Advanced Setting
Extra Close Time Extra Close Time
|||||||||||||||||......................
0 SEC.
This function allows to set the duration This function allows to set the duration TIME TIME of the of the CLOSING CLOSING extra pulse extra pulse
Change the value by pressing the UP or DOWN buttons and confi rm with OK. Change the value by pressing the UP or DOWN buttons and confi rm with OK.
Default value = 0 SEC. Default value = 0 SEC.
13) 13)
Advanced Setting
Fire Release Fire Release
Open/Free/Closed
When the Fire Release function is enabled, it’s possible to set the reaction of the door When the Fire Release function is enabled, it’s possible to set the reaction of the door
depending on the failure of the Fire power ( V+, V-) :
depending on the failure of the Fire power ( V+, V-) :
• • DOOR FREE DOOR FREE = In case of = In case of Fire Power Fire Power failure the door becomes FREE failure the door becomes FREE
• • DOOR OPEN DOOR OPEN = In case of = In case of Fire Power Fire Power failure the door opens and stays OPEN until failure the door opens and stays OPEN until
the fi re power is reset or the function of the the fi re power is reset or the function of the Menu Confi guration Menu Confi guration is disabled. is disabled.
• • DOOR CLOSED LOCKED DOOR CLOSED LOCKED = Door CLOSED and lock active = Door CLOSED and lock active
• • DOOR CLOSED UNLOCKED DOOR CLOSED UNLOCKED = = Door CLOSED and lock disactive Door CLOSED and lock disactive
14) 14)
Advanced Setting
Max Obst Cycles
Max Obst Cycles
|||||||||||||||||......................
000
When the door meets an obstacle during closing, it re-opens immediately. At the end of When the door meets an obstacle during closing, it re-opens immediately. At the end of
the pause time, it re-closes slowly. If the obstacle is still present the cycle restarts.
the pause time, it re-closes slowly. If the obstacle is still present the cycle restarts.
It is possible to set the max number of re-closing attempts by the door before stopping to
It is possible to set the max number of re-closing attempts by the door before stopping to
await a defi nitive command. Change this parameter (from
await a defi nitive command. Change this parameter (from 1 1 to to 256) 256) by pressing the by pressing the UP UP
or DOWN or DOWN buttons and confi rm with OK. buttons and confi rm with OK.
Default value = 4 attempts. Default value = 4 attempts.
15) 15)
Advanced Setting
Dynamic Pause Enable / Disable
The dynamic pause is a function which automatically adjusts the pause time The dynamic pause is a function which automatically adjusts the pause time
programmed, avoiding too many closing attempts of the door in high traffi c situations.
programmed, avoiding too many closing attempts of the door in high traffi c situations.
When enabled, this function increases by 1 sec. the pause time programmed each time
When enabled, this function increases by 1 sec. the pause time programmed each time
it detects
it detects a passage through the door during the closing phase, and restarts the time a passage through the door during the closing phase, and restarts the time
when the passage is detected against when the door is open. when the passage is detected against when the door is open.
Once the door completes its cycle up to the closed status, the pause time is reset to the
Once the door completes its cycle up to the closed status, the pause time is reset to the
programmed value.
programmed value.
Press UP or DOWN buttons to enable or disable the function and confi rm with OK
Press UP or DOWN buttons to enable or disable the function and confi rm with OK
Default value = DISABLE. Default value = DISABLE.
6) 6)
Advanced Setting
FTC-S Exclusion FTC-S Exclusion
|||||||||||||||||......................
000
If the door is next to a wall and is using a curtain protection device, it may be necessary If the door is next to a wall and is using a curtain protection device, it may be necessary
to prevent the device being activated by the wall to allow a complete opening of the leaf.
to prevent the device being activated by the wall to allow a complete opening of the leaf.
Set the zone width as percentage of the full door motion using the UP or DOWN buttons
Set the zone width as percentage of the full door motion using the UP or DOWN buttons
to increase or decrease the value.
to increase or decrease the value.
000 = Door OPEN 000 = Door OPEN
100 = Door CLOSED
100 = Door CLOSED
Example
Example : if you want to disable the curtain device when the leaf is open at the 80% of : if you want to disable the curtain device when the leaf is open at the 80% of
the complete travel, set the value to 20. the complete travel, set the value to 20.
WARNING: the excluded zone may become a health & safety hazard WARNING: the excluded zone may become a health & safety hazard
because it not protected!
because it not protected!
7) 7)
door door
FTC-S active zone FTC-S active zone
e
x
c
lu
d
e
d
z
o
n
e
excluded zone
wall wall
18
cdvi.com
cdvigroup.com
Advanced Setting
Ex Open Torque Ex Open Torque
|||||||||||||||||......................
50 %
This function allows to set the This function allows to set the TORQUE TORQUE of the of the OPENING OPENING extra pulse extra pulse
Change the value by pressing the UP or DOWN buttons and confi rm with OK. Change the value by pressing the UP or DOWN buttons and confi rm with OK.
Default value = 50% Default value = 50%
9) 9)
Advanced Setting
Extra Open Time
Extra Open Time
|||||||||||||||||......................
0 SEC.
This function allows to set the duration This function allows to set the duration TIME TIME of the of the OPENING OPENING extra pulse extra pulse
Change the value by pressing the UP or DOWN buttons and confi rm with OK. Change the value by pressing the UP or DOWN buttons and confi rm with OK.
Default value = 0 SEC. Default value = 0 SEC.
10) 10)
Advanced Setting
Ex Close Torque Ex Close Torque
|||||||||||||||||......................
50 %
This function allows to set the This function allows to set the TORQUE TORQUE of the of the CLOSING CLOSING extra pulse extra pulse
Change the value by pressing the UP or DOWN buttons and confi rm with OK. Change the value by pressing the UP or DOWN buttons and confi rm with OK.
Default value = 50% Default value = 50%
12) 12)