Digitronic CamCon DC33 страница 24 Скачать руководство пользователя

Страница: 24 / 25

Digitronic

Digital Cam Switch Unit

Automationsanlagen GmbH

CamCon DC33

10. Technical data of the CamCon

Multifunctional display for programming ............. 7-segment, 5-digits, 13mm

Number of outputs .............................................. 8 or 16

State display of the outputs................................. a red LED each

Number of programable cams ............................ 500

Number of programs ........................................... 1

Cycle time, (switching speed) ............................. 1ms

Dead time compensation (DTC) ......................... for each output

Range of the DTC ............................................... 0 to 255ms

Exactness of the DTC ......................................... +0 to -1 step

Encoder input ...................................................... synchronous serial (SSI), gray coded

Encoder type ....................................................... AAG60007

Encoder resolution .............................................. 360 steps / rotation

Zero point correction ........................................... electronical adjustment inside CamCon

Rotatory direction of the encoder ........................ is programmed by CamCon

Length of the connecting cable

between encoder and CamCon .......................... 200m

Data security/memory ......................................... EEPROM

Supply voltage..................................................... 24V DC ±20%

Encoder supply voltage ....................................... with 24V DC over supply voltage

of CamCon

Current reception ................................................ 200mA without encoder and outputs

Output current ..................................................... 500mA, short circuit proof permanent current

(see 4.3. The outputs)

Output voltage..................................................... 24V DC, pluse switching

Connections for:

Encoder............................................................... through plug block clips

Voltage supply..................................................... through plug block clips

Cam outputs........................................................ through plug block clips

Operating temperature........................................ 0°C to +55°C

Cover type for:

Front plate / full sight gate................................... IP 67 / IP 55

Cabinet................................................................ IP 40

Dimensions ......................................................... see fig. on page 10

Front plate part.................................................... 138 x 138mm + 1

Cabinet (switch plate cabinet by DIN 43700) ...... 144 x 144 x 63mm (WxHxD)

Cover of the front plate ....................................... Full sight gate, can be locked with security key

PC - connection................................................... with PC30 Software package

Weight................................................................. about 600g

Version from: 05.06.2018

Page: 24

Содержание CamCon DC33


























Результаты поиска

Содержание CamCon DC33

Отзывы:

Похожие инструкции для CamCon DC33

Бренды по названию

Популярные бренды

Digitronic CamCon DC33, Руководство пользователя

Результаты поиска

Содержание CamCon DC33

Отзывы:

Похожие инструкции для CamCon DC33

Бренды по названию

Популярные бренды