DigiTech Vocalist Live FX Скачать руководство пользователя страница 20

Страница: 20 / 76

Owner's Manual

Operating The Live FX

This section of the manual describes how to navigate and use the various features of

the Live FX.

Gold Channel Effects

The "Gold Channel" effect processing section is the first effect module in the

signal chain and provides channel strip style processing. The Gold Channel effects

comprise the following 8 effects: Warmth, Compressor, Pitch Correction, Ambience,

EQ, De-Esser, Gate, and Low Cut. These effects provide the sonic foundation for

your vocal sound and are used as the front end on all presets.

To globally bypass/enable the Gold Channel effects:
1. Press the <Gold Channel> button. When the Gold Channel button is lit, the

Gold Channel effects are enabled. When the button is not lit, these effects are

bypassed.

To edit Gold Channel settings:
1. Press and hold the <Gold Channel> button. The <Gold Channel> button

will begin flashing and the LCD display will now display the Gold Channel effect

parameters.

2. Start singing into the microphone or use the Sound Check feature (see

"Sound

Check" on page 18

for further information). Turn the <DATA> encoder

to select a Gold Channel Type. Think of these "Types" as pre-configured presets

for the Gold Channel parameters. Once you've selected the Gold Channel

Type which is close to the sound you are after, you can fine-tune the settings by

turning the corresponding <Edit> knobs.

3. Press the <DATA> encoder to navigate the various pages within the Gold

Channel Edit menu and use the corresponding <Edit> knobs to make any

further parameter adjustments.

4. When finished, press the <Gold Channel> button to exit.

NOTE:

Changes to Gold Channel effect parameters do not need to be stored to

a preset, since these effects are global and independent of presets.

Any changes made to Gold Channel Types are automatically stored. This lets you

setup different custom channel strip settings and easily switch between them. You

can always revert back to the factory default settings for any of the Gold Channel

types if necessary.

Содержание Vocalist Live FX













































































Результаты поиска

Содержание Vocalist Live FX

Отзывы:

Похожие инструкции для Vocalist Live FX

Бренды по названию

Популярные бренды

DigiTech Vocalist Live FX, Руководство пользователя

Результаты поиска

Содержание Vocalist Live FX

Отзывы:

Похожие инструкции для Vocalist Live FX

Бренды по названию

Популярные бренды