background image

June 1997

The information in this document is subject to change without notice and should not be construed as a

commitment by Digital Equipment Corporation.

Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth

in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS

252.227-7013.

FCC Note: 

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. Any changes or modification made to this equipment may

void the user’s authority to operate this equipment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio and television reception; however,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the following measures:

• 

Re-orient or relocate the receiving antenna.

• 

Increase the separation between the equipment and the receiver.

• 

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

DO NOT attempt to modify this equipment. If modified, the FCC may void your authority to operate this

equipment.

Canadian Department of Communications Statement

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment

Regulations.

Prioris, DEC, DECpc, and the DIGITAL logo are trademarks of Digital Equipment Corporation. Intel and

Pentium are registered trademarks of Intel Corporation.

 

 MS-DOS is a registered trademark of Microsoft

Corporation. All other trademarks and registered trademarks are the property of their respective holders.

 

1997 Digital Equipment Corporation.

All Rights Reserved.

Содержание Prioris XL 5166


















Отзывы: