Digital Equipment CELEBRIS XL Скачать руководство пользователя страница 83

Страница: 83 / 110

Digital CELEBRIS XL & XL

Troubleshoot

ing

MCS Logistics Engineering - Nijmegen

POST and Boot Error Messages

(continued)

Message

Problem

Solution

Shadow RAM Failed at offset:
nnnn

Shadow RAM failed.

Run the BIOS Setup utility and
disable failed shadow memory
region.

System battery is dead -
Replace and run SETUP

Battery/real-time clock failed.

Replace the battery and then run
the BIOS Setup utility to restore
previous configuration
information.

System cache error - Cache
disabled

RAM cache failed.

Run the BIOS Setup utility and
restore all settings to original
values. If the problem persists,
replace the defective cache
memory.

System CMOS checksum bad -
run SETUP

Battery/real-time clock failed.

Correct the address conflict using
the BIOS Setup utility. If the
problem persists, replace the
battery/real-time clock.

System RAM failed at offset:
nnnn

System RAM failed.

Run the BIOS Setup utility and
restore all settings to original
values. If the problem persists,
replace the defective memory.

System timer error

The timer test failed.

Run the BIOS Setup utility and
restore all settings to original
values. If the problem persists,
replace the defective component.

POST and Boot Informational Messages

Message

Description

nnnn Cache SRAM Passed

Where nnnn is the amount of computer cache (in kilobytes) that
tested successfully.

Entering SETUP

BIOS Setup utility runs.

Extended RAM Passed

Where nnnn is the amount of extended memory (in kilobytes) that
tested successfully.

nnnn Shadow RAM passed

Where nnnn is the amount of shadow RAM (in kilobytes) that tested
successfully.

System BIOS shadowed

This indicates that the BIOS has been successfully copied to shadow
RAM.

nnnn System RAM passed

Where nnnn is the amount of system RAM (in kilobytes) that tested
successfully.

UMB upper limit segment
address: nnnn

Displays the address of the upper limit of UMB. This indicates the
released segments of the BIOS that can be reclaimed by a virtual
memory manager.

Содержание CELEBRIS XL














































































































Результаты поиска

Содержание CELEBRIS XL

Отзывы:

Похожие инструкции для CELEBRIS XL

Бренды по названию

Популярные бренды

Digital Equipment CELEBRIS XL, Руководство по техническому обслуживанию

Результаты поиска

Содержание CELEBRIS XL

Отзывы:

Похожие инструкции для CELEBRIS XL

Бренды по названию

Популярные бренды