background image

 

INSTALLATION

 

Mounting:

 

The Model 3185E is designed to plug into a Model 3000RK 20-pin edge connector. All connections are 

intended  to  be  made  at  the  edge  connector  and  will  be  referred  to  in  this  manual  by  edge  connector 
number or letter. 

Pin Numbers and Functions:

 

Pin  numbers  are  listed  below  for  the  Model  3185E  when  plugged  into  a  3000RK  Connector.  Consult 

FIGURE 1 on page 4 for proper registration of pin numbers. 

PIN NUMBER 

FUNCTION 

 

1   Common terminal for relay output referenced to pins 9 and 10. 

2   Circuit common (ground). 

3   Circuit common (ground). 

5  Audio input low (audio input circuit common if unbalanced). 

6  Audio input high. 

8  +12 Volt D.C. power supply input. 

9  Normally closed contact for relay output referenced to pins 1 and 10. 

10  Normally open contact for relay output referenced to pins 1 and 9. 

Common terminal for relay output referenced to pins K and L. 

Reserved.  Connections to this pin will disable card. 

‘Set’ input. 

‘Reset’ input. 

Normally closed contact for relay output referenced to pins A and L. 

Normally open contact for relay output referenced to pins A and K. 

Содержание 637

















Отзывы: