manualshive.com logo in svg

Digikeijs DR5088RC DIGIDETECT, Руководство пользователя

Поделиться
Скачать
Digikeijs DR5088RC DIGIDETECT Скачать руководство пользователя страница 4

DR5088RC DIGIDETECT 

30.05.2019

 

P 4 

www.digikeijs.com 

 

1.2 Warranty provisions

 

 

All our products are covered by a 24-month manufacturer’s warranty. Please read this manual carefully. The warranty will be void in the event of damage to 
the product caused by incorrect adherence to this manual. 
CAUTION! Any warranty claims are void if the DR5088RC and/or the power supply housing are opened. 
 
 
Please read the following points carefully before you start working with the DR5088RC. 
 
Any warranty is void if the housing of the DR5088RC or of the power supply are opened. 
When working on your track, the control unit must be switched off at all times. 
Never connect an external voltage or other digital system to the Track exit of the DR5088RC control unit. 
This will damage the internal electronics in such a way that any warranty claims will be void. Even if this happens accidentally. 
Always use official and approved cabling to prevent short circuits and damage. 
Use the DR5088RC in a dry and dust-free environment 
 
 
 
 

 

CAUTION!!!! NEVER connect the DR5088RC via USB while this is connected to the TRACK INPUT or vice versa! 

 

The USB connection may only be used to configure the DR5088RC without that being connected to your model 

 

railway! When connecting both the USB and TRACK INPUT simultaneously, you will damage both the DR5088RC 

 

and your Central Unit 

 
 
 

 
 

1.3 Legal notices  

All rights, changes, typing and printing errors and delivery options are reserved. 
Specifications and illustrations are non-committal and non-binding. All changes to the hardware, firmware and software are reserved. 

Содержание DR5088RC DIGIDETECT












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды