Initialized mode
Function description
Auto save
User program
1-3
The function of this option is to automatically
save all settings of user, shut down the device
or suddenly power drop, then automatically
reload to the last status. Especially suitable
for situation that is tuning or often need to
change the device settings
.
Regardless of the status of the shutdown, the
corresponding user program (1 to 3) will be
automatically recalled on reboot. This function
suitable for situation of the KARAOK, in
order to reduce the workload of tuner.
Options [Initial] of the menu [Setup], to configure the initialized
mode, there are four options, Auto save and user program 1-3.
Initialized Mode Selection
Gain: -15dB to +12dB, step 0.1dB
Bandwidth: 0.011 to 3.595
(3) Low-cut and High-cut filters of subwoofer output:
Frequency of Low-cut filter: 19.7Hz – 1000Hz
Frequency of High-cut filter: 35.1Hz – 2000Hz
Roll-off of filters: 12dB, 18dB, 24dB, 36dB
Type of filters: Bessel, Butterworth, Linkwitz-Riley
(4) Volume of subwoofer output matrixes:
Volume of music: Mute, or -30dB to 0dB, step 0.5dB
Volume of direct sound: Mute, or -30dB to 0dB, step 0.5dB
(5) Phase inverter of subwoofer output: 0°/ 180°
(6) Delay of center output:
On / Off,
0.0mS to 21mS, step 0.1mS
(7) Compressor of subwoofer output:
Off / Hard-knee / Soft-knee type
Ⅰ
/ Soft-knee type
Ⅱ
/
Soft-knee type
Ⅲ
/ Soft-knee type
Ⅳ
/ Soft-knee type
Ⅴ
Threshold: -20dBu to 14.3dBu, step 0.5dBu
Ratio: 1:1 to 16:1, step 2:1
Setting Menu
1. To switch the various pages of setup menu by continue press
Key [setting]. Tips, press Key [ ] for back to last page, easy to
adjust the
parameters in front and back pages, if needed.
2. Twist the knob [EDIT] to adjust parameters.
3. Press key [ ] and [ ] to change the cursor's position of same
page, to adjust various parameters.
4. Setting parameters as follows:
(1) Initialized mode:
Auto save or User programs 1-3
(2) Limits of maximum volume:
Music: Mute, or -30dB to +12dB, step 0.5dB
Microphone: Mute, or -30dB to +12dB, step 0.5dB
Effect: Mute, or -30dB to +6dB, step 0.5dB
Main output: Mute, or -30dB to +6dB, step 0.5dB
Center output: Mute, or -30dB to +6dB, step 0.5dB
Subwoofer output: Mute, or -30dB to +10dB, step 0.5dB
(3) Limits of Gain of equalizer:
Music: +6.0dB to +12.0dB, step 0.1dB
Microphone: +6.0dB to +12.0dB, step 0.1dB
Effect: +6.0dB to +12.0dB, step 0.1dB
Main output: +6.0dB to +12.0dB, step 0.1dB
Center output: +6.0dB to +12.0dB, step 0.1dB
Subwoofer output: +6.0dB to +12.0dB, step 0.1dB
(4) Automatic recovery of music pitch:
On / Off
Threshold: -30dB to 0dB, step 0.5dB
Time: 0 to 60S
(5) Sing mode switch to disco:
Auto / Sing / Disco
Threshold: -30dB to 0dB, step 0.5dB
Time: 0 to 60S
Program Storage / Recall
1. Program storage
(1) Press Key [STO/RCL] to store program, then a
confirmation dialog appears, as shown below:
(2) Twist the knob [EDIT] to select the sequence number of
stack to be stored, the follow character indicates the status
of stack,“Used” or “Empty”.
(3) Press key [STO/RCL] to confirm, there will be two
situations:
If the status of stack is “Empty”, then will store directly to
finish the steps, Else if the status of stack is “Used”, a
confirmation dialog will appears again, as shown below:
Save to
User program 1? “Empty”
1
(4) Press key [ ] to cancel, key [ ] to confirm.
2. Program recall
There are two ways to recall the user program,
Ways1: Press keys [1],[2],[3] to recall the program 1-3 quickly
and directly.
Ways2:To recall more other user programs, the seteps as follows:
(1) Press and hold the Key [STO/RCL], to enter the program
recalling process, a dialog as follows,
(2) Twist knob [EDIT] to select the sequence number of stack
to be recalled, the follow character indicates the status of
stack, “Used” or “Empty”.
(3) Press key [SOT/RCL] again to confirm the sequence
number, tip recalling failed and exit the recalling process if
the stack is “Empty”. Otherwise forward to the final
confirmation if the stack is “Used”, dialog as shown below.
(4) Press key [ ] to cancel, key [ ] to confirm.
Cover user programs 1 ?
“ ”
: No “ ”: Yes
1
Recall
user program 1 ? “used”
Output Mode (Sing / Disco)
1. Function description:
(1) Each output port (Main left, Main right, Center,
Subwoofer) has two sets of equalizer and volume setting,
refer to sing mode and disco mode respectively;
(2) These two modes can be switched manually or
automatically, its working principle is that when all the
MIC input has no signal and reach the setted time, the
output will be switched to the disco mode. When any one of
the mic inputs is activated, working mode switched back to
the sing.
(3) The range of threshold that a signal from microphone
inputs can be considered effectively is: -30dB to 0dB, range
of time is: 0s to 60s.
2. Setting process:
(1) Select for sing mode manually, and set the parameters for
the equalizer and volume,
(2) Select for disco mode manually, and set the parameters for
the equalizer and volume,
(3) Set an appropriate threshold and time for the microphone,
and choose the auto mode, and then device will work well.
Recall user Memory 1 ?
“ ”
: No
“ ”
: Yes
Limits of Maximum Volume and Gain:
1. Function description:
To make the volume output in a certain range, the effective
5
