background image

 

9

 

7. 

Connect the charger to an electrical 

outlet.

8. 

Select the battery type and charge rate.

9. 

When charging is complete, 

disconnect the charger from the AC 

power, remove the clamps from the 

vehicle’s chassis, and then remove 

the clamp from the battery terminal.

CHARGING A BATTERY OUTSIDE  

OF THE VEHICLE

1. 

Place battery in a well-ventilated area.

2. 

Clean the battery terminals.

3. 

Connect the battery, following the 

precautions listed in sections 6 and 7.

4. 

Connect the charger to the electrical 

outlet.

5. 

Select the battery type and charge rate.

6. 

When charging is complete, 

disconnect the charger from the AC 

power, disconnect the negative clamp, 

and finally the positive clamp.

7. 

A marine (boat) battery must be 

removed and charged on shore.

AUTOMATIC CHARGING MODE

When an Automatic Charge is performed, 

the charger switches to the maintain mode 

automatically after the battery is charged. 

ABORTED CHARGE

If charging cannot be completed normally, 

charging will abort. When charging aborts, 

the charger’s output is shut off and the 

CHARGING (yellow/orange) LED will 

flash. The digital display will show an error 

code (see the Troubleshooting section 

for a description of the error codes). To 

reset after an aborted charge, unplug the 

charger from the AC outlet, wait a few 

moments and then plug it back in.

DESULFATION MODE

Desulfation could take 8 to 10 hours. If 

desulfation fails, charging will abort and the 

CHARGING (yellow/orange) LED will flash.

COMPLETION OF CHARGE

Charge completion is indicated by the 

CHARGED/MAINTAINING (green) LED. 

When lit, the charger has switched to the 

maintain mode of operation. 

MAINTAIN MODE  

(FLOAT-MODE MONITORING)

When the CHARGED/MAINTAINING 

(green) LED is lit, the charger has 

started maintain mode. In this mode, the 

charger keeps the battery fully charged 

by delivering a small current when 

necessary. If the charger has to provide 

its maximum maintain current for a 

continuous 12 hour period, it will go into 

abort mode (see Aborted Charge section). 

This is usually caused by a drain on the 

battery or the battery could be bad. Make 

sure there are no loads on the battery. If 

there are, remove them. If there are none, 

have the battery checked or replaced. 

MAINTAINING A BATTERY

The 28.71325 charges and maintains  

6 and 12 volt batteries, keeping them at 

full charge.

NOTE:

 The maintain mode technology 

allows you to safely charge and maintain 

a healthy battery for extended periods 

of time. However, problems with the 

battery, electrical problems in the 

vehicle, improper connections or other 

unanticipated conditions could cause 

excessive current draws. As such, 

occasionally monitoring your battery and 

the charging process is required.

USING THE ENGINE START SETTING

Your battery charger can be used to jump 

start your car if the battery is low. Follow 

all safety instructions and precautions for 

charging your battery. Wear complete eye 

protection and clothing protection. 

WARNING:

 Using the ENGINE START 

setting WITHOUT a battery installed in 

the vehicle could cause damage to the 

vehicle’s electrical system. 

NOTE:

 If you have charged the battery 

and it still will not start your car, do not 

use the Engine Start setting, or it could 

damage the vehicle’s electrical system. 

Have the battery checked.

1. 

With the charger unplugged from the 

AC outlet, connect the charger to the 

battery, following the instructions given 

in the CHARGING A BATTERY IN 

THE VEHICLE section.

2. 

With the charger plugged in and 

connected to the battery and chassis, 

press the RATE SELECTION button 

until the ENGINE START LED is lit. 

3. 

Crank the engine until it starts or 3 

seconds pass. If the engine does not 

start, wait 3 minutes before cranking 

again. This allows the charger and 

battery to cool down.

NOTE: 

During extremely cold weather,  

or if the battery is under 2 volts, charge 

the battery for 5 minutes before cranking 

the engine.

4. 

If the engine fails to start, charge the 

battery for 5 more minutes before 

attempting to crank the engine again.

5. 

After the engine starts, unplug the AC 

power cord before disconnecting the 

battery clamps from the vehicle.

Содержание 28.71325













Отзывы: