Diamondback 06.DB Скачать руководство пользователя | Manualshive

Страница: 30 / 38

background image

28

Appendix C

Wheel and Seat Post Quick Release Mechanisms

A. Quick Release Wheels

1. How a Wheel Quick Release Works

!

WARNING: Riding with an improperly adjusted wheel quick

release can allow the wheel to wobble or dis en gage from the

bicycle, causing serious injury or death to the rider. Therefore,

it is essential that you:

1. Ask your dealer to help you make sure you know how

to install and remove your wheels safely.

2. Understand and apply the correct technique for

clamping your wheel in place with a quick release.

3. Each time, before you ride the bike, check that the

wheel is securely clamped.

The wheel quick release uses a cam action to clamp the

bike’s wheel in place (see fi g.

19). Because of its adjustable

nature, it is critical that you understand how it works, how to use

it properly, and how much force you need to apply to secure

the wheel.

!

WARNING: The full force of the cam action is needed to

clamp the wheel securely. Holding the nut with one hand

and turning the lever like a wing nut with the other hand until

everything is as tight as you can get it will not clamp the wheel

safely in the dropouts.

a. Adjusting the quick release mechanism

The wheel hub is clamped in place by the force of the

quick release cam pushing against one dropout and pulling
the tension adjusting nut, by way of the skewer, against the
other dropout. The amount of clamping force is controlled
by the tension adjusting nut. Turning the tension adjusting nut
clockwise while keeping the cam lever from rotating increases
clamping force; turn ing it coun ter clock wise while keeping the
cam lever from rotating reduces clamping force. Less than half
a turn of the tension adjusting nut can make the difference
be tween safe clamping force and unsafe clamping force.

b. Front Wheel Secondary Retention Devices

Most bicycles have front forks which utilize a sec ond ary

wheel retention device to keep the wheel from disengaging if its
clamping mechanism is incorrectly adjusted. Secondary retention
devices are not a sub sti tute for correct wheel clamping.

Secondary retention devices fall into three basic categories

(see Section 4.B fi gs. 12a, b &c):
(1)   The clip-on type is a part which the manufacturer adds
to the front wheel hub or front fork (fi g. 12a).
(2)   The integral type is molded, cast or machined into the
outer faces of the front fork dropouts (fi g. 12b).
(3)   The washer type is a hat-shaped washer which fi ts into

«
...
28
29
30
31
32
...
»

Содержание 06.DB







































Отзывы:

Нет отзывов

Похожие инструкции для 06.DB

Бренд: wayscral Страницы: 184

Бренд: BMW Страницы: 15

BLUE PAPER TERRA HYDRO 2022

Бренд: Orbea Страницы: 45

Бренд: Puky Страницы: 88

Бренд: Air Bike Страницы: 8

Reach City(Trekking)

Бренд: PACIFIC CYCLE Страницы: 11

Бренд: Puky Страницы: 16

Бренд: Puky Страницы: 56

Бренд: Puky Страницы: 148

Бренд: Ice Страницы: 40

Бренд: WHISKY PARTS Co Страницы: 2

Бренд: Nordic Cab Страницы: 25

Бренд: Planet Bike Страницы: 2

Бренд: Detroit Bikes Страницы: 24

Бренд: Cycle Torch Страницы: 9

Бренд: Marzocchi Страницы: 29

Бренд: Kellys Страницы: 45

Бренд: Canyon Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды