manualshive.com logo in svg

Diamond Systems ZIRCON-MM, Руководство пользователя

Поделиться
Скачать
Diamond Systems ZIRCON-MM Скачать руководство пользователя страница 9

ZIRCON-MM

 User Manual v2.11 © 2002 Diamond Systems Corporation P. 9 

7. REGISTER MAP 

 

Base + Write Read  

0 Analog Output A/D register 
1 Analog Output (duplicate) A/D register (duplicate) 
2 Start A/D conversion -- 
3 Start A/D conversion (duplicate) -- 
4 Control register Status register 
5 Control register (duplicate) Status register (duplicate) 
6 -- -- 
7 -- -- 
8 Digital I/O port A (82C55) Digital I/O port A 
9 Digital I/O port B Digital I/O port B 
10 Digital I/O port C Digital I/O port C 
11 Digital I/O configuration register -- 
12 Counter/timer 0 data (82C54) Counter/timer 0 data 
13 Counter/timer 1 data Counter/timer 1 data 
14 Counter/timer 2 data Counter/timer 2 data 
15 Counter/timer configuration register Counter/timer configuration register 
 
A/D, D/A, Control, and Status register definitions are shown starting on the next page. For digital I/O 
and counter/timer register definitions, refer to the 82C55 and 82C54 datasheets, respectively. 
Counter/timers are not available on model ZMM-LC. 
 
 

Содержание ZIRCON-MM












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды