manualshive.com logo in svg

Diamond Systems ZIRCON-MM, Руководство пользователя

Поделиться
Скачать
Diamond Systems ZIRCON-MM Скачать руководство пользователя страница 3

ZIRCON-MM

 User Manual v2.11 © 2002 Diamond Systems Corporation P. 3 

1. GENERAL DESCRIPTION 

 
ZIRCON-MM is a PC/104 format I/O module with 8 analog inputs, 1 analog output, 24 digital I/O 
lines, 3 16-bit counter/timers (DX version), and 1 interrupt line. Both the analog input and output 
resolution are 8 bits (1/256). The analog circuitry requires no calibration over the lifetime of the 
product. 
 
The digital I/O is based on an 82C55 chip with 3 8-bit ports and one configuration register. All I/O 
lines are TTL and CMOS compatible. 
 
The counter/timers are based on an 82C54 chip with 3 16-bit counter/timers and one configuration 
register. Two counters are cascaded together to form a 32-bit counter/timer; The input to this 
combined counter/timer is driven by an on-board 4MHz clock oscillator. The third counter/timer is 
available at the I/O header. All I/O lines are TTL  and CMOS compatible. 
 
ZIRCON-MM is an 8-bit bus module and conforms to the physical and electrical specifications for 8-
bit PC/104 modules published in the PC/104 Specification, Version 2.1, July 1994. As it is an 8-bit 
module, it does not contain the 16-bit expansion bus connector. 
 
One 50-pin right-angle pin headers is provided for all I/O. The pinout of this header is defined at the 
end of this manual. All digital I/O signals are TTL compatible. 
 
Three versions are available: 
 

ZMM-LC:

 Contains no counter/timer; all analog I/O is unipolar (positive voltages) only. 

ZMM-DX:

 Contains the counter/timer; analog I/O can be unipolar or bipolar. 

 
ZIRCON-MM operates on +5V power supply only. Model ZMM-DX provides an on-board DC/DC 
converter to p/-5V for the analog circuitry. Model ZMM-LC uses the 5V and ground 
for the analog supply. 
 

Содержание ZIRCON-MM












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды