background image

19

20

©2005 Diamond Audio Technology. All Rights Reserved

©2005 Diamond Audio Technology. All Rights Reserved

D6 5.2

Pushing this button “IN” inverts the phase of the sub channels by 180 degrees. Pushing 
this button “OUT” keeps the sub channels in phase.

Sub Channel Inversion

Crossover Freq. Diagrams

Pushing this button “IN” engages the Highpass filter. Pushing this button “OUT” will 
bypass the filter.  There is one of these switches for each of the front, rear and center 
channels.

Highpass On/Off

It is possible to completely run your D5 5.1 off of only one set or input RCA’s.  The rear, 
center, and sub channels can all be slaved of the front channels inputs.  Simply push the 
appropriate button “IN” to slave that channel to those inputs.  You can also slave just the 
center and sub channels if you have a four channel input.

Slave Select

Pushing this button “IN” engages the sub-sonic filter on the sub channels. Pushing this 
button “OUT” will bypass the filter.

Subsonic On/Off

Turning this control sets the sub-sonic filter point from 17 Hz (fully counterclockwise) to 
80 Hz (fully clockwise).

Subsonic Freq.

Pushing this button “IN” engages the lowpass filter on the sub channels. Pushing this 
button “OUT” will bypass the filter.

Lowpass On/Off

Turning this control sets the lowpass crossover point from 60 Hz (fully counterclockwise) 
to 250 Hz (fully clockwise).

Lowpass Freq.

Subsonic

Lowpass

D6 5.2

Содержание D6 300.4













Отзывы: