manualshive.com logo in svg

Diaglobal DP 310, Руководство по эксплуатации

Поделиться
Скачать
Diaglobal DP 310 Скачать руководство пользователя страница 22

Step by step instructions 

GOT 442 / GPT 442 

Number of samples per series: Up to 6 samples at the same time 

Additionally required: Dry block thermostat (30 minutes preheated)

 

        Diaglobal GmbH · Köpenicker Straße 325 · 12555 Berlin · +49 (0)30 6576 2597 · [email protected] · www.diaglobal.de                        2021-01 

1. 

Incubate cuvettes in preheated  

dry block thermostat for 7 minutes 

2. 

Transfer 50 µL of the sample 

(serum/plasma) with an end-to-end 
capillary into each cuvette  
Do not mix yet! 

3. 

Screw starter cap on and mix well 

Then insert the cuvette immediately 
into the dry block thermostat 

5. 

Start measurement with ON/ENTER 

Time (1 minute) counts backwards. All 
cuvettes remain in the dry block  
thermostat during this time 
Double signal tone: The M1 
measurement starts in 30 seconds! 
  

4. 

Switch photometer on with    

ON/ENTER key 
Wait for device check, confirm with 
ON/ENTER 
Select GOT or GPT, confirm with 
ON/ENTER 

6. 

Note: When inserting the cuvette 

into the photometer, make sure that the 
capillary is positioned at the side of the 
cuvette wall and aligns with the black 
arrow on the front foil 
This ensures that the measurement is 
not disturbed by the capillary. 

ON 

ENTER 

ON 

ENTER 

                    GOT 
 GOT Measurement

 

 
           START 

9. 

All measured values can now be 

displayed one after the other by 
pressing the right arrow key 

7. 

Follow

 

the display, insert sample 1 into 

the photometer, „Measuring“ is displayed, 
wait for 10 seconds 
Then remove the cuvette and incubate it 
again 
Proceed in the same way with all other 
cuvettes in the correct order 
Then press ON/ENTER 

8. 

Time (10 minutes) counts 

backwards. All cuvettes remain in the 
dry block thermostat during this time 
Double signal tone: The M2 
measurement starts in 30 seconds!  
For the M2 measurement follow the 
display in the same way as discribed in 
Fig. 7  

ON 

ENTER 

M2                 GOT 
Sample        09:30 
incubate  
 

 

M1                GOT 
Samples      00:30 
incubate 
 

 

ON 

ENTER 

Result            GOT 
Sample 01 
        40 U/L  
 

 

ON 

ENTER 

M1                 GOT 
Sample 02    00:03 
insert or 
         ENTER 

 

Содержание DP 310































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды