manualshive.com logo in svg

Diablo Controls, Inc. DSP-13, Руководство пользователя

Поделиться
Скачать
Diablo Controls, Inc. DSP-13 Скачать руководство пользователя страница 13

DSP-13 User Manual 

Page 13 of 16

 

DSP13_MAN_B 

6.

 

Configuration 

Sensitivity 

The  ten  position  rotary  switch  is  used  to  set  the  sensitivity.    For  most 
installations the setting of 5 will work well.  If motorcycle detection is required, 
you may need to use a higher setting. 

One second after changing the sensitivity setting, the detector will automatically 
reset itself to implement the new sensitivity setting.  The technician must make 
sure that there are no vehicles or other objects over or near the sensor when the 
reset occurs.  If the zone was not clear, simply press the  reset button once the 
zone is clear. 

DIP Switches 

There are two DIP switches for adjusting the configuration of the TRIAD system.  
There are no internal DIP switches or jumpers to configure. 

When a DIP switch is moved to the left position it  is in the ON condition.  The 
right position is OFF. 

Pulse  /  Presence  (Switch  2)

  –  This  switch  determines  if  the  detector  operates 

using  presence  detection  or  pulse  detection.    The  switch  setting  takes  effect 
immediately when changed. 

OFF = the presence mode of operation is selected.  ON = the pulse mode of operation is selected. 

Fail  Type  (Switch  1)

  –  This  switch  determines  if  the  output  operates  in  a  fail-safe  or  fail-secure  mode  of 

operation. 

During  fail-safe  operation,  when  the  detector  is  in  the  presence  mode  of  operation  and  a  sensor  failure  is 
detected,  the  output  will  stay  activated  during  the  failure.  In  gate  applications  this  feature  is  used  to 
automatically open the gate if a sensor fails. 

During  fail-secure  operation,  when  the  detector  is  in  the  presence  mode  of  operation  and  a  sensor  failure  is 
detected, the output will stay deactivated during the failure. In gate applications this feature is used to keep the 
gate closed if a sensor fails.  

It should be noted that a power failure will always result in a  fail-secure operation.  Fail-safe operation is only 
available when a valid input voltage is applied to the detector.  When configured for pulse mode the output will 
always operate in the fail-secure mode. 

OFF = the fail-safe mode of operation is selected.  ON = the fail-secure mode of operation is selected. 

 

Содержание DSP-13

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды