DH Instruments FPG8601 Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 166

background image

FPG8601™/VLPC™ OPERATION AND MAINTENANCE MANUAL

© 2007 DH Instruments, a Fluke Company

Page 128

8.5

MOUNTING POST PRT CALIBRATION

The temperature as read by the mounting post PRTs is used to determine the thermal expansion of the
piston-cylinder effective area. The temperature is also used to monitor temperature rate of change and
temperature change from the time of zero. Accuracy of these PRTs is critical to proper FPG operation.
This section describes how to remove and calibrate these sensors.

The temperature sensor inside the lubricating volume of the FPG is used only for an indication of
temperature change. The value is not used for FPG pressure determination. Therefore, this sensor is

not directly calibrated.

8.5.1

REMOVE THE PRT

S

Make sure that the FPG is vented in gauge mode. Then turn the power off.

Detach the PRT cable from the FPG platform by unscrewing the connection in a counter
clockwise direction.

Remove each PRT from the mounting post by unscrewing the knurled nut from each
mounting post PRT. Note that there are two o-rings that hold each PRT into the
mounting post. Remove and save these o-rings.

Remove the knurled nut from each PRT.

8.5.2

CREATE THE PRT CABLE ADAPTER

Refer to Figure 66 to create an adaptor cable to calibrate the PRT.

Figure 66.

PRT Calibration Cable Adaptor

Table 47.

PRT Calibration Cable Connections

FROM

TO

SIGNAL

P1-1 E1

I

Source

P1-2 E3

Upper

(,1)

+

P1-3

E4

Upper (,1) -

P1-4 E2 I

Ret

P1-5 E5

Lower

(,2)

+

P1-6

E6

Lower (,2) -

«
...
138
139
140
141
142
...
»

Содержание FPG8601







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FPG8601

Бренд: Zetkama Страницы: 6

Бренд: Facility Explorer Страницы: 4

Бренд: Daikin Страницы: 5

Бренд: Gardner Denver Страницы: 22

Бренд: B&G Страницы: 2

Бренд: Hama Страницы: 7

Бренд: Hama Страницы: 44

Бренд: RadioMaster Страницы: 10

Бренд: K&K Страницы: 6

Бренд: Parker Страницы: 42

Бренд: SMC Networks Страницы: 31

Бренд: Grundfos Страницы: 80

Бренд: Chamberlain Страницы: 4

Бренд: Shimaden Страницы: 16

Бренд: Danfoss Страницы: 20

Automation PC 810

Бренд: B&R Страницы: 428

Бренд: Potter Страницы: 4

Vesta Building Controller

Бренд: Vestamatic Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды