DFI SR330-N Скачать руководство пользователя страница 8

Страница: 8 / 155

Introduction

Processor

Chipset

System Memory

Expansion Slots

Graphics

Audio

LAN

Serial ATA

IDE

Chapter 1 - Introduction

Specifications

• Intel

Core

2 Duo mobile processor

- 800/533MHz system data bus

• Intel

Celeron

M 500 series processor for mobile Intel

965

Express chipset

• Processor socket: mPGA478P

• Intel

chipset

- Intel

GME965 Express chipset

- Intel

82801HBM I/O Controller Hub (ICH8M)

• Two 240-pin DDR2 DIMM sockets
• Supports 533MHz and 667MHz DDR2 SDRAM
• Supports maximum of 4GB system memory

• 1 PCI Express x16 slot
• 1 PCI Express x4 slot
• 2 PCI slots

• Internal graphics feature

- Mobile Intel

Graphics Media Accelerator X3100

- Dynamic Video Memory Technology 4.0
- Microsoft DirectX 9x
- OpenGL 1.5

• Integrated graphics interface

- Analog CRT

- Integrated 300MHz RAMDAC
- Analog monitor supports up to QXGA (2048x1536@60Hz)

- LVDS

- 25MHz-112MHz single/dual channel, TFT panel type support
- Single/Dual channel LVDS interface support:

2 x 24 bpp panel suppor ts up to WUXGA
(1920X1200@65Hz) or UXGA (1600x1200@75Hz)

- DVI (supports DVI-D signal only)

- DVI 1.0 support for external digital monitor

• Realtek ALC262 2-channel High Definition Audio
• Two 24-bit stereo DACs and three 20-bit stereo ADCs
• S/PDIF input/output interface

• Two Realtek RTL8111C PCI Express Gigabit controllers
• Supports 10Mbps, 100Mbps and 1Gbps data transmission
• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) compliant

• Three Serial ATA por ts, compliant with SATA 1.0a

specification

• Data transfer rate up to 3Gb/s
• Supports Advanced Host Controller Interface (AHCI)

• Supports up to two IDE devices
• Supports Ultra ATA 100/66/33

Содержание SR330-N




























































































































































Результаты поиска

Содержание SR330-N

Отзывы:

Похожие инструкции для SR330-N

Бренды по названию

Популярные бренды

DFI SR330-N, Руководство пользователя

Результаты поиска

Содержание SR330-N

Отзывы:

Похожие инструкции для SR330-N

Бренды по названию

Популярные бренды