DFI PR810-C622 Скачать руководство пользователя страница 45

Страница: 45 / 47

Chapter 4

RAID

User's Manual |

PR810-C622

Chapter 4 - RAID

The system board allows configuring RAID on Serial ATA drives. It supports RAID 0, RAID 1,

RAID 5 and RAID 10.

RAID Levels

RAID 0 (Striped Disk Array without Fault Tolerance)

RAID 0 uses two new identical hard disk drives to read and write data in parallel, interleaved

stacks. Data is divided into stripes and each stripe is written alternately between two disk

drives. This improves the I/O performance of the drives at different channel; however it is not

fault tolerant. A failed disk will result in data loss in the disk array.

RAID 1 (Mirroring Disk Array with Fault Tolerance)

RAID 1 copies and maintains an identical image of the data from one drive to the other drive.

If a drive fails to function, the disk array management software directs all applications to the

other drive since it contains a complete copy of the drive’s data. This enhances data protection

and increases fault tolerance to the entire system. Use two new drives or an existing drive and

a new drive but the size of the new drive must be the same or larger than the existing drive.

RAID 5

RAID 5 stripes data and parity information across hard drives. It is fault tolerant and provides

better hard drive performance and more storage capacity.

In the case of RAID5, you need to check the Parity errors immediately after each boot. If

some parity errors are found, verify and repair them first, and then restart after confirming

that the parity errors are 0.

Please confirm that Parity errors is 0 again after turning on the device before removing the

SSD (Degraded)

RAID 10 (Mirroring and Striping)

RAID 10 is a combination of data striping and data mirroring providing the benefits of

both RAID 0 and RAID 1. Use four new drives or an existing drive and three new drives for

this con-figuration.

5$,'/HYHO

0LQ'ULYHV

3URWHFWLRQ

'HVFULSWLRQ

RAID 0

None

Data striping without redundancy

RAID 1

Single Drive Failure

Disk mirroring

RAID 5

Single Drive Failure

Block-level data striping with

distributed parity

RAID 10

1 Disk Per Mirrored

Stripe (not same mirror)

Combination of RAID 0 (data striping)

and RAID 1 (mirroring)

Setup Procedure

To enable the RAID function, the following settings are required.

1. Install SATA drives.

2. Enable RAID in the Insyde BIOS.

3. Create a RAID volume.

3-1. Create a RAID volume if the boot type is UEFI.

4. Install the Intel Rapid Storage Technology Utility.

Step 1: Install SATA Drives

Refer to chapter 2 for details on connecting the Serial ATA drives.

Step 2: Enable RAID in the Insyde BIOS

1. Power-on the system then press <Del> to enter the main menu of the Insyde BIOS.

2. Go to “Advanced” menu and select the “SATA Configuration” menu.

3. Change the “Configure SATA as” to “RAID”.

4. Save the changes in the “Exit” menu and teboot the system, or press "F10" and "yes".

Important:

1. Please make sure the SATA drives that you are to create a RAID volume with

are connected and powered, and are able to be detected by the system. Other-

wise, the RAID BIOS utility would not be accessible.

2. While creating a RAID volume, please make sure the system, drives, and cables

are perfectly steady and mounted correctly. Disturbance during creating a

RAID volume will result in irreversible data corruption sotred on the drive.

Содержание PR810-C622
















































Результаты поиска

Содержание PR810-C622

Отзывы:

Похожие инструкции для PR810-C622

Бренды по названию

Популярные бренды

DFI PR810-C622, Руководство пользователя

Результаты поиска

Содержание PR810-C622

Отзывы:

Похожие инструкции для PR810-C622

Бренды по названию

Популярные бренды