25
User's Manual |
KS-SD
Chapter 5
Buzzer
USB 3-4
USB 3.0
USB 1-2
USB 3.0
Power LED
HDD LED
J22
JP2
JP3
J21
HDMI (default)/DP
DVI
System
Fan 2
1
Front
Panel
5
1
1
1
1
1
4
SATA Power
-
DC-in
LAN 2
LAN 1
PCIe x16 (PCIE1)
SPI Flash
BIOS
9
1
2
10
COM 4
VGA
1
6
(JP4)
Clear CMOS
Data (JP1)
Auto Power-on
Select (JP11)
1
6
(JP9) (JP16)
1
6
6
1
(JP8) (JP15)
1
6
6
1
(JP10)
1
2
10
COM 3
1
(JP6)
6
6
9
1
2
10
COM 2
9
1
2
(JP7) (JP14)
6
6
1
2
1
2
10
COM 1
9
1
2
16
LPC
1
2
14
4-pin DC-out
1
1
2
3
4
PCIe x4 (PCIE2)
Power Button
Reset
DDR4_2 SODIMM
DDR4_1 SODIMM
1
(JP5)
6
6
1
1
1
6
6
2
2
2
6
1
4
STB_LED
2
25
26
Parallel
1
DIO Power
DIO
S/PDIF
Front Audio
2
5
1
1
10
9
ECX
+
SATA 3.0
(JP13)
1
1
(JP12)
1
SATA 0
SATA 1
1
Mini PCIe
mSATA
System
Fan 1
1
1
bettery
1
1
1
2
12
USB 2.0
9
COM 2
COM 1
SATA (Serial ATA) Connectors
• 2 Serial ATA 3.0 ports
- SATA port 0 and 1 with data transfer rate up to 6Gb/s
Features
The Serial ATA connectors are used to connect the Serial ATA device. Connect one end of the
Serial ATA data cable to the SATA connector on the system board and the other end to your
Serial ATA device.
The power cable must be connected from the system board’s Serial ATA power connector to a
SATA drive’s power connector in order to provide power to the drive. Refer to the next page
for pin definitions of the SATA power connectors.
BIOS Setting
Configure the Serial ATA drives in the Advanced submenu (“SATA Configuration” section) of the
BIOS. Refer to Chapter 7 for more information.
SATA 0/1
7
RXN
GND
TXP TXN
GND
1
RXP
GND
SATA 3.0 6Gb/s
Front Panel Connector
Buzzer
USB 3-4
USB 3.0
USB 1-2
USB 3.0
Power LED
HDD LED
J22
JP2
JP3
J21
HDMI (default)/DP
DVI
System
Fan 2
1
Front
Panel
5
1
1
1
1
1
4
SATA Power
-
DC-in
LAN 2
LAN 1
PCIe x16 (PCIE1)
SPI Flash
BIOS
9
1
2
10
COM 4
VGA
1
6
(JP4)
Clear CMOS
Data (JP1)
Auto Power-on
Select (JP11)
1
6
(JP9) (JP16)
1
6
6
1
(JP8) (JP15)
1
6
6
1
(JP10)
1
2
10
COM 3
1
(JP6)
6
6
9
1
2
10
COM 2
9
1
2
(JP7) (JP14)
6
6
1
2
1
2
10
COM 1
9
1
2
16
LPC
1
2
14
4-pin DC-out
1
1
2
3
4
PCIe x4 (PCIE2)
Power Button
Reset
DDR4_2 SODIMM
DDR4_1 SODIMM
1
(JP5)
6
6
1
1
1
6
6
2
2
2
6
1
4
STB_LED
2
25
26
Parallel
1
DIO Power
DIO
S/PDIF
Front Audio
2
5
1
1
10
9
ECX
+
SATA 3.0
(JP13)
1
1
(JP12)
1
SATA 0
SATA 1
1
Mini PCIe
mSATA
System
Fan 1
1
1
bettery
1
1
1
2
12
USB 2.0
9
COM 2
COM 1
ATX-SW
Front
Panel
HDD-LED - HDD LED
This LED will be lit when the hard drive is being accessed.
RESET SW - Reset Switch
This switch allows you to reboot without having to power off the system.
ATX-SW - ATX Power Switch
This switch is used to power on or off the system.
PWR-LED - Power/Standby LED
When the system’s power is on, this LED will be lit. When the system is in the S1 (POS - Pow-
er On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend
To RAM) state, it will blink every 4 seconds.
Pin Pin Assignment
Pin Pin Assignment
HDD-LED
3
HDD Power
PWR-LED
2
LED Power
5
Signal
4
LED Power
RESET SW
7
Ground
6
Signal
9
RST Signal
ATX-SW
8
Ground
11 N.C.
10
Signal
RESET-SW
HDD-LED
PWR-LED
2
1
