Dexter Power 3901316953, Перевод оригинального руководства пользователя

Страница: 34 / 92

34 | GB
10.3 Cutting particle boards
To prevent the cutting edges from cracking when
working with particle boards, you should not set the
saw blade (3) more than 5mm greater than the thick
-
ness of the workpiece (also see 9.2).
11. Transport
1. Turn off the power tool before any transport and
disconnect it from the power supply.
2. Apply the power tool at least with two people, do
not touch the table extensions.
3. Protect the power tool from knocks, bumps and
strong vibrations, such as during transport in ve -
hicles.
4. Secure the power tool against overturning and
sliding.
5. Never use the safety devices for handling or
transporting purposes.
12. Maintenance
m
Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
12.1 General maintenance measures
- Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
down with compressed air at low pressure.
- We recommend that you clean the equipment im -
mediately after you use it.
- Clean the equipment regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plastic
parts in the equipment. Ensure that no water can
get into the interior of the equipment.
- In order to extend the service life of the tool, oil the
rotary parts once monthly. Do not oil the motor.
- Clean the dust collection systems by blowing out
with compressed air.
12.2 Brush inspection
- In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important. The carbon brushes should not be re
-
placed by anyone but a qualified electrician.
12.3 Overload switch
The device motor is protected against overload with
an overload switch (11a).
In the event of the nominal current being exceeded,
the overload switch (11a) switches the device off.
If this happens, proceed as follows:
- Let the device cool down for several minutes.
- Press the overload switch (11a).
- Switch the device on by pressing the green “I” but -
ton.
- Place your hands (with fingers closed) flat on the
workpiece and push the workpiece along the paral
-
lel stop (15) and into the blade (3).
- Guide at the side with your left or right hand (de -
pending on the position of the parallel stop) only
as far as the front edge of the saw blade guard (4).
- Always push the workpiece through to the end of
the splitter (6).
- The offcut piece remains on the saw table (1) until
the blade (3) is back in its position of rest.
- Secure long workpieces against falling off at the
end of the cut (e.g. with a roller stand etc.) (e.g.
roller table etc.)
10.1.1 Cutting narrow workpieces (fig. 20)
Be sure to use a push stick (9) when making longi -
tudinal cuts in workpieces smaller than 120 mm in
width. A push block is supplied with the saw! Replace
a worn or damaged push stick immediately..
- Adjust the parallel stop to the width of workpiece
you require. (see 9.4)
- Feed in the workpiece with two hands. Always use
the push stick (9) in the area of the saw blade.
- Always push the workpiece through to the end of
the splitter.
m
Caution! With short workpieces, use the push stick
from the beginning.
10.1.2 Making angular cuts (fig. 21)
Angular cuts must always be made using the parallel
stop (15).
- Set the blade to the desired angle. (See 9.3)
- Set the parallel stop (15) in accordance with the
workpiece width and height (see 9.4)
- Carry out the cut in accordance with the workpiece
width (see 10.1).
10.2 Making cross cuts (fig. 22)
- Slide the cross stop (7) into one of the grooves
(31a/b) in the table and adjust to the required an
-
gle. (see 9.5). If you also want to tilt the blade (3),
use the groove (31a) which prevents your hand and
the cross stop from making contact with the blade
guard.
- Use the stop rail.
- Press the workpiece firmly against the cross stop
(7).
- Switch on the saw.
- Push the cross stop (7) and the workpiece toward
the blade in order to make the cut.
- Important:
Always hold the guided part of the workpiece.
Never hold the part which is to be cut off.
- Push the cross stop (7) forward until the workpiece
is cut all the way through.
- Switch off the saw again. Do not remove the offcut
until the blade has stopped rotating.