manualshive.com logo in svg

Dexter Laundry Wn0600ea-13en2x-sskcs-usx, Руководство по запчастям и обслуживанию

Поделиться
Скачать
Dexter Laundry Wn0600ea-13en2x-sskcs-usx Скачать руководство пользователя страница 123

The contol voltage is 115 vac ( 60hz) or 24 vac (50hz) to heat relay. Machine availlable in 208/240 vac 3 

phase (60hz), 380/415 vac 3 phase (50hz) ONLY. Optional Temperature control board can be added for 

non-heated machines to display temperatures and Steam option kit available . Steam valve will operate the 

same as descibed throughout except valve will operate in place of heat relay.

Troubleshooting

If the heater relay does not engage in a heated bath:

Check the calibration switch is set to run position, Check that I/O board jumpers are changed to the level 

side, Jumper must start closest to level input light and open pin will be towards door input lights.

Check actual water temperature is less than programmed temperature

Check the temperature sensor for open circuit or shorted

Check low level contacts on the pressure switch not closing

Check low level safety relay contacts not closing or bad contacts

Check low level safety relay coil

Check heater relay contacts not closing or bad contacts

Check wiring between temperature board and sensor at all connectors and inspect wires for any damage.

If temperature control board is removed, the programmed temperature value is retained in all baths and 

the water valves to fill that bath are chosen based on the programmed temperature as described on previ

-

ous feature page.

Calibration

The calibration should be checked whenever a temperature sensor has been replaced or if actual water 

temperature varies significantly from the display. To calibrate the temperature control board go to step 

#15 of the diagonstic cycle (#31). Actual temperature will be shown in display. On the temperature control 

board move the cal-run switch to the calibrate position. The factory set calibration

temperature of 98 degrees C should show on the display after a few seconds. Now turn the adjusting screw 

clockwise to increase calibration point and display temperature or counterclockwise to decrease calibration 

point and display temperature. The display is updated every 5 seconds so make adjustments in very small 

increments. Be sure to allow ample time for display to respond to updates. If adjustments of higher than 

100 degrees C only the last two digits will be displayed.

208-240 vac 3 phase (60hz) 308-415 vac 3 phase (50hz) power is supplied on L-1, L-2, L-3 to the normally 

open contacts of the heat relay and then to the six heating elements. The elements are wired in star or wye 

on 50HZ models. A delta configuration is used on 60HZ models. There is a potential 220 volts across each 

element for both models 60HZ or 50HZ. Control voltage 115 vac (60hz) or 24 vac (50hz) is used to power 

the heat relay coil and will close the heat relay contacts. The supply voltage will intiate from the I/O board 

Terminal number #6 (wht/blue wire) through the low-level safety relay contacts and then to the heat relay 

operating coil when heat is being called for by temperature board. The neutral will be supplied from the 

(blu/yel) wire connected to AC neutral terminal on the I/O board. The low level safety relay coil will operate 

when the washer has filled to a level, and gets a signal from the pressure switch. That signal will be 24 VDC 

and comes from the CPU board and through the pressure switch.

With the low level safety relay contacts now switched and closed, voltage now passes to the heat relay 

operating coil, and allow main 3 phase voltage across the heating elements. Control voltage 115 vac (60hz) 

is used to power the steam valve coil. The supply voltage will intiate from the I/O board Terminal number 6 

(wht/blue wire) to the heat relay coil when heat is being called for by temperature board. The neutral will 

be supplied from the (blu/yel) wire connected to AC neutral terminal on the I/O board. The valve gets a 

signal from the pressure switch. That signal will be 24 VDC and comes from the CPU board and through the 

pressure switch. With the low level safety relay contacts now swtiched and closed, voltage now will pass to 

the heat relay operating coil, and allow main 3 phase voltage across the heating element.                              

Part # 8533-097-001  11/16

123

Содержание Wn0600ea-13en2x-sskcs-usx
































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды