Dewetron DAQP-CFB2 Скачать руководство пользователя страница 5

Страница: 5 / 22

Safety Instructions

Safety instructions for DEWETRON amplifiers

The DEWETRON data acquisition systems and amplifiers may only be installed by experts.

Read your manual carefully before operating.

Observe local laws when using the amplifiers.

Ground the equipment: For Safety Class 1 equipment (equipment having a protective earth terminal), a

non interruptible safety earth ground must be provided from the mains power source to the product input

wiring terminals or supplied power cable.

DO NOT operate the product in an explosive atmosphere or in the presence of flammable gases

or fumes.
DO NOT operate damaged equipment: Whenever it is possible that the safety protection features built

into this product have been impaired, either through physical damage, excessive moisture, or any other

reason, REMOVE POWER and do not use the product until safe operation can be verified by service-

trained personnel. If necessary, return the product to a DEWETRON sales and service office for service

and repair to ensure that safety features are maintained.
Keep away from live circuits: Operating personnel must not remove equipment covers or shields.

Procedures involving the removal of covers or shields are for use by service-trained personnel only.

Under certain conditions, dangerous voltages may exist even with the equipment switched off. To avoid

dangerous electrical shock, DO NOT perform procedures involving cover or shield removal unless you

are qualified to do so.
No modifications are allowed at the amplifiers.

DO NOT service or adjust alone. Do not attempt internal service or adjustment unless another person,

capable of rendering first aid and resuscitation, is present.

DO NOT substitute parts or modify equipment: Because of the danger of introducing additional hazards,

do not install substitute parts or perform any unauthorized modification to the product. Return the product

to a DEWETRON sales and service office for service and repair to ensure that safety features are

maintained.

DO NOT touch internal wiring!

DO NOT use higher supply voltage than specified!

Use only original plugs and cables for harnessing.
Safety of the operator and the unit depend on following these rules.

450134 • DAQP/H

/PAD Modules • Technical Reference Manual • Prin

ing version 2.3.4 • November 18, 2020

Содержание DAQP-CFB2























Результаты поиска

Содержание DAQP-CFB2

Отзывы:

Бренды по названию

Популярные бренды

Dewetron DAQP-CFB2, Техническое справочное руководство

Результаты поиска

Содержание DAQP-CFB2

Отзывы:

Бренды по названию

Популярные бренды