Dewetron DAQP-CFB2 Скачать руководство пользователя страница 11

Страница: 11 / 22

DAQP-CFB2

120 Ω

100 kΩ

±7 V

±7 V, 50 mA

100 kΩ

TEDS

100 Ω

33 pF

100 kΩ

Inductive

full bridge

100 Ω

100 kΩ

350 Ω

50 kΩ

1 kΩ

x10

x100

x1000

x10

OFFSET

DAC

Phase

adjustment

±90 °

Sine generator

0.6 to 20 kHz

Single

master

Crystal

oszillator

PLL

REF

Slave

Master

2.5 V

RMS

CLK

EXC+

SENSE+

R+

IN+

IN-

SENSE-

EXC-

TEDS

GND

order

reconstruc-

tion fi lter

0.48 x f

order

lowpass fi lter

10 Hz to 3 kHz,

OFF

}

Quarter bridge completion

Shunt

INPUT

CONNECTOR

OUTPUT

CONNECTOR

9-pin DSUB

9
4

SYNC

IN / OUT

OUT

DAQP-CFB2

Apply shunt:

Press the

FILTER

button for more than 3 seconds to apply the internal shunt

resistor as long as you keep the button pressed.

Apply Zero ref.:

Press the

RANGE

button for more than 3 seconds to shortcurcuit the module input

as long as you keep the button pressed.

Amplifier balance: Press the

RANGE

button for more than 3 seconds (zero reference). Keep the

RANGE

button pressed and push the

FILTER

button in addition. This will set

the module offset to zero. The calibration values will be stored in the module!

This function is independent from the sensor and takes approx. 2 seconds!

Sensor balance:

Press both

RANGE

and

FILTER

button together for more than 2 seconds.

This will set the offset of a connected sensor to zero. The sensor offset

correction is working within ±400 % of full scale range.

Factory default:

Press both

RANGE

and

FILTER

button at power up for approx. 3 seconds to

set the amplifier to factory default settings (full bridge, 100 mV/V, 5 V

RMS

Bessel, module address 0x00, 100 kΩ shunt, power-on-default off,

manual

control).

Free variable gain and offset

The programmable gain amplifier (PGA) combined with the variable gain amplifier (VGA) allow a wide input

gain from 0.1 mV/V to 1000 mV/V. The offset is free programmable between ±400 % of the input with a

resolution of 17 bit. So it is possible to normalize almost any sensor signal to the ±5 V amplifier output.

450134 • DAQP/H

/PAD Modules • Technical Reference Manual • Prin

ing version 2.3.4 • November 18, 2020

Содержание DAQP-CFB2























Результаты поиска

Содержание DAQP-CFB2

Отзывы:

Бренды по названию

Популярные бренды

Dewetron DAQP-CFB2, Техническое справочное руководство

Результаты поиска

Содержание DAQP-CFB2

Отзывы:

Бренды по названию

Популярные бренды