DeWalt XR DCS512 Скачать руководство пользователя страница 15

Страница: 15 / 60

English

OPERATION
Instructions for Use

WARNING:

Always observe the safety instructions and

applicable regulations.

WARNING:

To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.

An accidental

start‑up can cause injury.

Prior to Operation

• Make sure the guards have been mounted correctly. The

saw blade guard must be in closed position.

• Make sure the saw blade rotates in the direction of the

arrow on the blade.

• Do not use excessively worn saw blades.

Mounting the Dust Extraction Port (Fig. A, E)

Your circular saw is supplied with a dust extraction port.

To Install the Dust Extraction Port

1. Fully loosen depth adjustment lever

2. Place the shoe

in the lowest position.

3. Push the dust extraction port

onto the circular saw

upper guard and align with the mounting holes. Secure
dust extraction port to the upper guard using the two
screws

provided.

Mounting and Adjusting the Rip Fence
(Fig. M)

The rip fence

is used for cutting parallel to the edge of

the workpiece.

Mounting

1. Slacken the rip fence adjustment knob

to allow the rip

fence to pass.

2. Insert the rip fence

in the base plate as shown.

3. Tighten the rip fence adjustment knob

Adjusting

1. Slacken the rip fence adjustment knob

and set the rip

fence

to the desired width. The adjustment can be read

on the rip fence scale.

2. Tighten the rip adjustment knob

Kerf Indicator (Fig. A)

The front of the saw shoe has a kerf indicator

for vertical

and bevel cutting. This indicator enables you to guide the saw
along cutting lines penciled on the material being cut. The kerf
indicator lines up with the left (inner) side of the saw blade,
which makes the slot or “kerf” cut by the moving blade fall to
the right of the indicator. Guide along the penciled cutting line
so that the kerf falls into the waste or surplus material.

Bevel Angle Adjustment (Fig. A, I)

The full range of the bevel adjustment is from 0 ° to 50 °. The
quadrant is graduated in increments of 1 °. On the front of the
saw is a bevel angle adjustment mechanism consisting of a
calibrated quadrant and a bevel adjustment lever

To Set the Saw for a Bevel Cut

1. Loosen (counterclockwise) the bevel adjustment lever

and tilt shoe (

, Fig. A) to the desired angle by aligning the

pointer with the desired angle mark.

2. Retighten lever firmly (clockwise).

Cutting Depth Adjustment (Fig. A, H)

1. Hold the saw firmly and loosen (clockwise) the depth

adjustment lever

and move shoe (

, Fig. A) to obtain the

desired depth of cut.

2. Make sure the depth adjustment lever has been retightened

(counterclockwise) before operating saw.

For the most efficient cutting action, set the depth adjustment
so that one‑half tooth of the blade will project below the
material to be cut. This distance is from the tip of the tooth to
the bottom of the gullet in front of it. This keeps blade friction
at a minimum, removes sawdust from the cut, results in cooler,
faster sawing and reduces the chance of kickback. A method
for checking for correct cutting depth is shown in Figure H. Lay
a piece of the material you plan to cut along the side of the
blade, as shown, and observe how much tooth projects beyond
the material.

Blades

WARNING:

To minimize the risk of eye injury, always

use eye protection. Carbide is a hard but brittle material.
Foreign objects in the workpiece such as wire or nails
can cause tips to crack or break. Only operate saw when
proper saw blade guard is in place. Mount blade securely
in proper rotation before using, and always use a clean,
sharp blade.

WARNING:

Do not cut metal, plastic, concrete, masonry

or fiber cement materials with this saw.

Do not use abrasive wheels or blades. A dull blade will cause
slow inefficient cutting, overload on the saw motor, excessive
splintering, and could increase the possibility of kickback.
Please refer to the table below to determine the correct size
replacement blade for your model saw.

Blade Diameter

Teeth

Application

140 mm

General purpose cutting

3. Release the lever and observe the guard

return to the

fully closed position.

The tool should be serviced by a qualified service center if it:
•  fails to return to the fully closed position,
•  moves intermittently or slowly, or
•  contacts the blade or any part of the tool in all angles and

depth of cut.