DeWalt DXV23P, Руководство пользователя

Страница: 17 / 83

15
1
Top handle/cord wrap
2
Power cord
3
3
On/off power switch
4
4
Vacuum head
5
4
5
5
Canister latch
6
Canister
7
9
7
7 13
5
4
6
Suction hose
8
Casters
9
Filters
10
10
10
10
hose inlet
11
Hose strap
12
14
14
9
12
Bag
English
Description (Fig. A)
ASSEMBLY AND ADJUSTMENTS (Fig. A–C)
OPERATION
Instructions for Use (Fig. A, D, E)
WARNING:
Always observe the safety instructions
and applicable regulations.
WARNING: To reduce the risk of injury,
turn appliance off and disconnect
appliance from power source before
installing and removing accessories,
before adjusting or changing set-ups or
when making repairs. An accidental start-up can
cause injury.
1. Plug the power cord into an appropriate outlet.
2. Turn the on/off switch to the ON position ( I ).
3. Your D
E
WALT construction dust extractor is fitted
with the D
E
WALT connection system. The allows for
a fast, secure connection between the suction hose
and power tool. The connector connects
To Convert Back to Dry Vacuum
Operation (Fig. A)
1. Empty Canister, refer to To Empty Canister
instructions.
WARNING : Never modify the power appliance or
any part of it. Damage or personal injury could result.
directly to DeWALT compatible tools or through the
use of an adapter (available from your local D
E
WALT
supplier). Refer to the Accessories section for detail
on available adapters.
NOTE:
If using an adapter ensure it is firmly
attached to the tool outlet before following the steps
below.
OPERATING INSTRUCTIONS
Caster installation (Fig. A, F)
1. Invert the dust box and install the casters to the bottom
of the dust tank and fix them with screws.
2.Return dust tank assembly upright.
Remove / Change Used Dust Collection
Bag (Fig. A)
WARNING:
Appropriate personal protective
equipment like dust mask and gloves should be used
while handling used dust bags.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch canister latches and remove vacuum
head .
3. Pull the collection bag carefully from inlet .
4. Seal the collection bag opening tightly when removing
it from the machine.
5. Dispose of collection bag in appropriate container
according to statutory provisions.
Wet Pick Up Applications (Fig. A, G)
WARNING:
If foam or liquid escapes from the
machine,switch off immediately.
CAUTION:
Clean the water level limiting device
regularly and examine it for signs of damage.
Refer to Fig. G.
NOTICE:
DO NOT remove ball float , doing so
will cause damage to the vacuum. The ball float keeps
water from entering the motor.
Before using the vacuum for wet pick up:
• Ensure the canister is empty and free of excessive dust.
• Remove filters .
WARNING: Do not use the machine with this set
up for dust Class L.
To Empty Canister (Fig. A, G)
The ball float valve will block air to the motor when
the canister is full and the sound of the motor will
change at once.
When the motor has a high pitched sound and air/
water flow stops, empty the canister.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch canister latches and remove vacuum
head .
3. Empty contents of canister into a suitable
container or drain.
WARNING: To reduce the risk of injury, turn
appliance off and disconnect appliance from
power source before installing and removing
accessories, before adjusting or changing
set-ups or when making repairs.
An accidental
start-up can cause injury .
WARNING: The filters must always be in
place while vacuuming, except as described
under
Wet Pick Up Applications under Operation .
When vacuuming fine dust, you may also use an
additional paper bag or fleece bag to make
emptying the canister easier.
1. If optional paper or fleece bag is to be used,
install as shown in Figure B.
NOTE : Be careful not to tear the bag. Place bag
securely onto inlet to provide a tight seal for
maximum dust collection performance.
2. Place the vacuum head onto the canister and
secure it by closing the canister latches .
3. Insert end of hose into threaded hose inlet
and tighten the end of hose on to the tank.