EN
10
ENGLISH
3.1.19
W
arning
.
DO NOT allow vehicles to drive over the high pressure hose.
3.1.20
W
arning
.
DO NOT move the appliance by pulling on the high pressure hose.
3.1.21
W
arning
.
When directed towards tyres, tyre valves or other pressurised
components, the high pressure jet is potentially dangerous. Do not use the
rotating nozzle kit, and always keep the jet at a distance of at least 30 cm during
cleaning.
3.1.22
W
arning
.
The use of non-original accessories and any other spare parts not
specifically intended for the model in question is prohibited. All modifications to
the appliance are prohibited; any modifications shall render the Declaration of
Conformity null and void and relieve the manufacturer of all liability under civil
and criminal law.
3.2 SAFETY “MUSTS”
3.2.1
W
arning
.
All electrical conductors MUST BE PROTECTED against the water jet.
3.2.2
W
arning
.
The electric supply connection must be made by a qualified electrician
and comply with IEC 60364-1. Either a residual current device that will cut off
the power supply if the leakage current to earth exceeds 30 mA for 30 ms or a
ground fault interrupt device must be installed.
3.2.3
W
arning
.
DURING start-up, the appliance may cause network noise.
3.2.4
W
arning
.
Use of a residual current breaker (RCB) will provide additional
protection for the operator (30 mA).
3.2.5
W
arning
.
Models supplied without plug must be installed by qualified staff.
3.2.6
W
arning
.
Use only approved electrical extension leads with suitable conductor
cross-section.
3.2.7
W
arning
.
Always turn off the switch when leaving the appliance unattended.
3.2.8
W
arning
.
High pressure may cause parts to rebound: wear all the protective
clothing (PPE) and equipment needed to ensure the operator’s safety.
3.2.9
W
arning
.
Before doing work on the appliance, REMOVE the plug.
3.2.10
W
arning
.
Before pressing the trigger, GRIP the gun firmly to counteract the recoil.
3.2.11
W
arning
.
COMPLY WITH the local water supply authority regulations.
Under IEC 60335-2-79, the appliance may only be connected to the mains
drinking water supply if the supply hose is fitted with a backflow preventer valve
with drain facility corresponding to EN 12729 type BA. The backflow preventer
can be ordered from the manufacturer.
EN - 4
Содержание DXPW001E
