12
13
English
English
LCD INDICATORS
When the appliance is turned OFF
When the appliance is turned ON
When charging a battery pack while the
appliance is turned off, a large battery image
is displayed in the center of the LCD screen
showing the battery pack charging status.
When the DWST08810 is on, indicators for
the power supply and the battery status are
displayed on the lower right portion of the LCD
screen.
Battery pack is empty
Appliance is operating via the AC/
DC power adaptor
Battery pack level is low
Battery level is low
Battery pack is partially charged
Battery is partially charged
Battery pack is fully charged
Battery is fully charged
Hot/Cold Delay
This charger has a hot/cold delay
feature: when the charger detects a
battery that is hot, it automatically
starts a delay, suspending charging
until the battery has cooled. After
the battery has cooled, the charger
automatically switches to the
pack charging mode. This feature
ensures maximum battery life.
Hot/Cold delay of charging
Faulty Battery Packs
This charger will not charge a
faulty battery pack. The charger
will indicate faulty battery pack by
displaying an X on the LCD battery
image. If this occurs, re-insert the
battery pack into the charger. If the
problem persists, try a different
battery pack to determine if the
charger is working properly. If the
new pack charges correctly, then
the original pack is defective and
should be returned to a service
center or other collection site for
recycling. If the new battery pack
elicits the same trouble indication
as the original, have the charger
and the battery pack tested at an
authorized service center.
NOTE:
This could also mean a
problem with a charger
Problem with the battery pack or
charger
CHARGING A BATTERY PACK
The DWST08810 includes a top compartment
that is mainly used to store and protect the
AC/DC power adaptor when not in-use.
1. Open the top compartment to take out
the AC/DC power adaptor (see Figure 1
and Figure 3).
2. Plug the charger AC/DC power adaptor
into an appropriate outlet and connect it
to the DWST08810 power-in port before
inserting the battery pack (see Figure 2).
3. Open the battery pack cover by releasing
its two latches (see Figure 2).
WARNING:
To reduce the risk of injury, turn the appliance off and disconnect it from the
power outlet when not in use and when making repairs.
DO NOT
attempt to disassemble the
unit; take it to an authorized service center when service or repair is required.
OPERATION
The DWST08810 will operate when
connected with the AC/DC power adaptor
and/or when operated solely on battery
power.
NOTE:
When the DWST08810 is connected
by the supplied power supply unit to the
outlet it will charge the installed battery.
Unplugged, the appliance can run up to
8 hours on a fully charged battery using a
premium 20V MAX* 2 Ah Li-ion battery. Using
batteries of lower voltage and amp hours will
yield less run time.
This appliance can be operated in the vertical
or horizontal position.
* With respect to 20V MAX* - Maximum
initial battery voltage (measured without a
workload) is 20 volts. Nominal voltage is 18.
Button Functions
The front panel includes a selection dial and
pushbuttons.
.......Selection dial (the selection dial has
more than one function)
...........On/Off button
...........Back button
...........Source selection button
...........Bluetooth button
........Preset buttons
Powering ON and OFF
Press the POWER button (
) for 1 second.
The appliance turns on to the last selected
audio source.
Press the POWER button (
) for 3 seconds.
The appliance turns off.
4. Insert the battery pack (not included)
into the charger, making sure the pack is
fully seated in the charger
(see Figure 4). The battery indicator
image will blink continuously, indicating
that battery charging is in process.
NOTE:
Close the battery pack cover and
check it is tightly closed.
5. The completion of charging will be
indicated by a steady battery indicator
image. The pack is fully charged and
may be used at this time or left in the
charger.
