DeWalt DWS778, Оригинальное руководство пользователя

Страница: 33 / 148

31
EnGLIsh
Date Code Position (Fig. B)
The Date Code 33 , which also includes the year of manufacture, is printed
into the housing.
Example:
2019 XX XX
Year of Manufacture
Description (Fig. A, B)
WARNING:
Never modify the power tool or any part of it. Damage or
personal injury could result.
1 Trigger switch
2
Guard lock-up release lever
3 Fixed upper guard
4
Outer flange
5 Blade bolt
6
Lower blade guard
7 Saw blade
8
Fixed table
9 Kerf plate
10
Mitre arm
11 Mitre latch
12
Rotating table/mitre arm
13 Mitre scale
14
Mitre scale screws
15
Sliding fence
16
Dust extraction port
17
Rail lock knob
18
Bench mounting holes
19
Material clamp
20 Base extension handles
21
Bevel clamp handle
22 Bevel override button
23
45° bevel adjustment stop screw
24 Bevel scale
25
Lock-down button
26 Rails
27
Saw head
28 Hex keys
29
Cable clamp
30 Padlock hole
31
XPS Worklight on/off switch
32 Spindle lock
33
Date code
Intended Use
Your D
e
WALT cross-cut mitre saw has been designed for professional
cutting of wood, wood products, plastics and aluminium. It performs the
sawing operations of cross-cutting, bevelling and mitring easily, accurately
and safely.
When assembled with a suitable saw blade, this machine is designed for
cutting aluminium profiles up to a maximum thickness of 4.0 mm.
nEVER
cut magnesium.
This unit is designed for use with a nominal blade diameter 250 mm carbide
tip blade.
DO nOT use under wet conditions or in presence of flammable liquids
or gases.
These miter saws are professional power tools.
DO nOT
let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
WARNING!
Do not use the machine for purposes other than intended.
•
Young children and the infirm.
This appliance is not intended for use
by young children or infirm persons without supervision.
• This product is not intended for use by persons (including children)
suffering from diminished physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are supervised by a person
responsible for their safety. Children should never be left alone with
this product.
ASSEMBLY
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing and
removing accessories, before adjusting or changing set-ups
or when making repairs.
Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
Unpacking
The motor and guards are already assembled onto the base.
Cable Clamp (Fig. C)
Verify the cable runs through the cable clamp 29 . Allow enough cable for
the saw head to travel, then tighten the clamp by means of the screw.
Bench Mounting (Fig. B)
1. Holes 18 are provided in all four feet to facilitate bench mounting.
Two different sized holes are provided to accommodate different sizes
of bolts. Use either hole; it is not necessary to use both. Always mount
your saw firmly to prevent movement. To enhance the portability, the
tool can be mounted to a piece of 12.5 mm or thicker plywood which
can then be clamped to your work support or moved to other job sites
and reclamped.
2. When mounting your saw to a piece of plywood, make sure that the
mounting screws do not protrude from the bottom of the wood.
The plywood must sit flush on the work support. When clamping the
saw to any work surface, clamp only on the clamping bosses where
the mounting screw holes are located. Clamping at any other point will
interfere with the proper operation of the saw.
3. To prevent binding and inaccuracy, be sure the mounting surface is not
warped or otherwise uneven. If the saw rocks on the surface, place a
thin piece of material under one saw foot until the saw is firm on the
mounting surface.
Assembling the Base Extensions (Fig. V)
WARNING: Base extensions must be assembled to both sides of
the saw's base before using the saw.
1. Locate the holes above the hand indentations on the side of the base.
2. Using a hex wrench, attach the bolt
47 through the nut 48 , through
the base extension handle 20 , and into the holes on the base.
3. Ensure the extension is secure by pulling on the extension to verify
no movement.
4. Repeat steps 1 through 3 on the other side.
nOTE: Make sure the extensions are level with the work surface so that the
workpiece rests evenly. A straight workpiece should have no gap between it
and the base extensions.
Changing or Installing a New Saw Blade (Fig. A, D, E)
WARNING :
To reduce the risk of injury, wear gloves when handling
the saw blade.
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing and
removing accessories, before adjusting or changing set-ups
or when making repairs.
Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
• Never lock the spindle while the blade is under power or coasting.
• Do not cut light alloy and ferrous metal (containing iron or steel)
or masonry or fibre cement product with this mitre saw.