52
EnGLIsh
MAINTENANCE
Your
D
e
WALT
power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Lubrication (Fig. T)
The motor and bearings require no additional lubrication. If
raising and lowering the blade becomes difficult, clean and
grease the height adjustment screws:
1. Unplug the saw from power source.
2. Turn the saw on its side.
3. Clean and lubricate the height adjustment screw
threads
42
on the underside of this saw as shown in
Figure T. Use general purpose grease.
Cleaning (Fig. A, S)
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect machine from
power source before cleaning.
An accidental start-up
can cause injury.
WARNING:
Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING:
Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: To reduce the risk of injury,
regularly clean
the table top.
WARNING: To reduce the risk of injury,
regularly clean
the dust collection system.
The blade guard assembly
11
and throat plate must be placed
in position before operating the saw.
Before use, carefully inspect upper and lower blade guards as
well as the dust extraction tube to determine that it will operate
properly. Ensure that chips, dust or work piece particles cannot
lead to blockage of one of the functions.
In case workpiece fragments are jammed between saw blade
and guards, disconnect the machine from the power supply
and follow the instructions given in section
Mounting the
saw blade
. Remove the jammed parts and reassemble the
saw blade.
Keep the ventilation slots clear and regularly clean the housing
with a soft cloth.
Regularly clean the dust collection system:
1. Unplug the saw.
2. Turn the saw on its side, so the bottom, open part of the
unit is accessible.
3. Open the dust access door
44
shown in Figure S loosening
the two screws and then by pressing the side clips
45
toward each other. Clean out the excess dust, and re-secure
by pushing the side clips completely into place then
tightening the lock screws.
Optional Accessories
WARNING:
Since accessories, other than those offered
by
D
e
WALT
, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
D
e
WALT
recommended
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Replace blade guard when worn. Contact your local
D
e
WALT
service centre for details on a blade guard replacment.
saW BLaDEs:
ALWAYS USE 250 mm noise reduced saw blades
with 30 mm arbour holes. Blade speed rating must be at least
5000 RPM. Never use a smaller diameter blade. It will not be
guarded properly.
BLaDE DEscRIPTIOns
aPPLIcaTIOn
DIaMETER
TEETh
construction saw Blades
(fast rip)
General Purpose
250 mm
24
Fine Crosscuts
250 mm
40
Woodworking saw Blades
(provide smooth, clean cuts)
Fine crosscuts
250 mm
60
Consult your dealer for further information on the
appropriate accessories.
• DWE74911 Rolling Table Saw Stand
• DWE74912 Scissor Leg Stand
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com
.
Содержание DWE7492
