English
6
min .....................minutes
or DC ......direct current
...................... Class I Construction
(grounded)
…/min ..............per minute
BPM ....................beats per minute
IPM .....................impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM ....................strokes per minute
A .........................amperes
W ........................watts
or AC ...........alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
no .......................no load speed
n .........................rated speed
......................earthing terminal
.....................safety alert symbol
.....................visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating.
D
e
WALT
tools are factory tested;
if this tool does not operate, check power supply.
COMPONENTS (FIG. A)
WARNING:
Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.
Intended Use
Your heavy-duty small angle grinder has been designed
for professional grinding, sanding, wire brush, and cut-off
applications at various work sites (i.e., construction sites).
DO nOT
use under wet conditions or in presence of
flammable liquids or gases.
Your heavy-duty small angle grinders is a professional
power tool.
DO nOT
let children come into contact with the
tool. Supervision is required when inexperienced operators
use this tool.
Features
DWE46253
E-switch Protection™
The ON/OFF switch has a no-volt release function. In the
event of a power outage or other unexpected shut down,
the switch will need to be cycled (turned off and then on)
to restart tool.
E-Clutch™
This unit is equipped with an E-Clutch™ (Electronic Clutch),
which in the event of a high-load or wheel pinch, the unit
will be shut off to reduce the reaction torque to the user.
The switch needs to be cycled (turned off and then on) to
restart tool.
Brake
When the switch is released the motor immediately turns
off and electronically brakes stopping the accessory quickly.
Kickback Brake™
When a severe pinch, stall, or bind-up event is sensed the
electronic brake engages with maximum force to quickly
stop the wheel, reduce the movement of the grinder, and
shut the grinder off. The switch needs to be cycled (turned
off and then on) to restart tool.
Constant Clutch™
When overloaded or stalled the motor torque is reduced. If
load is reduced the torque and RPM will increase. If the tool
is stalled for an extended amount of time it will shut-off and
require the switch to cycle to restart.
Variable Speed Dial (Fig. A)
WARNING:
Regardless of the speed setting, the rated
speed of the accessory must be at least equal to the
maximum speed marked on the power tool.
The variable speed dial offers added tool control and
enables the tool to be used at optimum conditions to suit
the accessory and material.
• Turn the dial
9
to the desired level. Turn the dial to the
right for higher speed and to the left for lower speed.
LED Indicator (Fig. A)
The LED indicator
10
will remain lit green during normal
activity, or blink in a pattern of red light to alert you a
tool protection feature has been activated. Refer to the
LED Guide
at the back of this manual for explanations of
blink patterns.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Accessories
The capacity of the DWE46253 is 5" (125 mm) x 1/4"
(6.35 mm) grinding wheel or 5" diamond surface wheel with
included surface finishing shroud.
It is important to choose the correct guards, backing pads
and flanges to use with grinder accessories. See page 13 for
information on choosing the correct accessories.
WARNING:
Handle and store all abrasive wheels
carefully to prevent damage from thermal shock, heat,
mechanical damage, etc. Store in a dry protected area
free from high humidity, freezing temperatures or
extreme temperature changes.
Guards
CAUTION: Guards must be used with all grinding
wheels, cutting wheels, sanding flap discs, wire
brushes, and wire wheels.
The tool may be used
without a guard only when sanding and polishing
with conventional sanding and polishing bonnets.
Refer to Figure A to see guards provided with the
Содержание DWE46253
Страница 47: ......
