DeWalt DWE46225, Оригинальное руководство пользователя

Страница: 23 / 92

21
EnGLIsh
When using the grinder for cutting metal or masonry a Type 1
guard MUST be used. Type 1 guards are available at extra cost
from
D
e
WALT distributors.
1. Place the angle grinder on a table, spindle
26
up.
2. Align the lugs 30 with the notches 22 .
3. Press the guard
29
down and rotate it to the
required position.
4. Securely tighten the screw
31
.
5. To remove the guard, slacken the screw.
NOTICE:
If the guard cannot be tightened by the adjusting
screw, do not use the tool. To reduce the risk of personal
injury, take the tool and guard to a service centre to repair
or replace the guard.
Mounting and Using Diamond Cutting
Wheels (Fig. A, F, G)
WARNING: Only diamond wheels with a negative
rake angle shall be used with cutting shroud . Do not
cut metal. Do not use with bonded abrasive wheels.
1. With the cutting shroud attached to the grinder, press the
front shroud button
7
and the side shroud button
8
at the
same time to fully open the cutting shroud.
2. Install the backing flange, 12 or 14 , on spindle 26 .
IMPORTanT: The DWE46225 comes with two sets of
flanges. Refer to the Flange/Grinder Compatibility Chart at
the end of this section for proper use.
3. Place the wheel 25 on the locking flange 11 or 13 ,
and place both on the spindle, against the backing
flange, centreing the wheel on the raised centre of the
backing flange.
4. While depressing the spindle lock button, tighten the
locking flange:
- Tighten standard locking flange using a wrench.
5. After the diamond cutting wheel is mounted, the cutting
shroud must be closed by pressing the front shroud
button
7
and the side shroud button
8
at the same time.
6. To remove the wheel, depress the spindle lock button and
loosen the locking flange.
Flange / Grinder compatibility chart
Flange set Grinder
Short (silver) flange set:
Locking flange 11
Backing flange 12
DCG405, DCG406
Flange / Grinder compatibility chart
Flange set Grinder
Long (black) flange set:
Locking flange 13
Backing flange 14
DWE4016, DWE4203, DWE4206,
DWE4207, DWE4216, DWE4217,
DWE4227, DWE4233, DWE4235,
DWE4237, DWE4238, DWE4246,
DWE4257, DWE4263, DWE4277,
DWE46105, DWE4357, DWE4347,
DWE4369, DWE4377, DCG412,
DCG414, D28498, DWE490,
DWE492, DWE494, DWE496,
DWE4001, DWE4056, DWE4057,
DWE4156, DWE4157, DWE4151,
DWE4557, DWE4559, DWE4579,
DWE4597, DWE4599
Depth of Cut Adjustment (Fig. A)
1. Loosen the depth of cut adjustment knob 5 .
2. Slide the depth of cut adjustor
4
to the desired position.
note: If the shroud is closed, press the front shroud
button
7
to open the shroud. This will make it easier to
move the depth of cut adjustor.
3. Tighten the depth of cut adjustment knob.
Dust Extraction (Fig. A, H)
WARNING: Use only power tools recommended by
D
e
WALT with this attachment.
For more information about D
e
WALT power tools compatible
with this attachment, please contact one of the authorized
services centres listed on the back cover or refer to the full
details of our after-sales service available on the Internet at:
www.2helpU.com .
WARNING: This attachment must be used with a dust
extractor system. ALWAYS wear certified safety face or
dust mask.
nOTE: Ensure hose connection is secure.
nOTE: The amount of dust retained by the dust extractor
vacuum is dependent on its filter system. Refer to the dust
extractor vacuum instruction manual for more information.
All
D
e
WALT dust collection shrouds are designed to work with
the D
e
WALT Airlock DWV9000 connector.
1. Attach the DWV9000 connector 23 to your dust collector
hose 24 .
2. Unlock the DWV9000 connector 23 and slide onto dust
port 1 .
3. Lock the DWV9000 connector 23 to secure.
Traditional Dust Extractor Vacuum Hoses
Attach recommended dust extractor vacuum hose to dust
port
1 .
Removing and Attaching Wheels (Fig. I)
This cutting shroud comes with four removable wheels
6
on the
metal base 3 which can be detached if not needed.
1. Remove the clips 27 holding the wheels to the base.